Altronix NetWaySP4 Installation Manual Download Page 6

 

- 6 - 

NetWaySP4 Series Installation Guide

Configuring Units for Network Connection

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Please be sure to visit altronix.com for latest

firmware and installation instructions

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Factory Default Settings

•  IP Address:  

192.168.168.168

•  User Name:  

admin

•  Password:  

admin

1.  Set the static IP address for the laptop to be used for programming to the same network IP address as the 

  NetwaySP4. The default address of the NetwaySP4 is 192.168.168.168, E.I. 192.168.168.200.

2.  Connect one end of the network cable to the network jack on the NetwaySP4 and the other to the network 

  connection of the laptop.

3.  Open a browser on the computer and enter “192.168.168.168” into the address bar. 

  A dialog box Authentication Required will appear requesting both user name and password. 

  Enter the default values here. Click on the button labeled 

Log In

4.  The status page of the NetWaySP4 will appear. Click on the tab labeled 

Network Settings

  This will open the Network Setting screen. In this screen the MAC Address of the NetWaySP4 module will 

  be found along with the Network Settings and Email Settings.

Network Settings:

In the IP Address Method field select the method that the IP Address for the NetWaySP4 will be obtained 

(STATIC or DHCP), then follow the appropriate steps.

Static: 

  A.  IP Address: Enter the IP address assigned to the NetWaySP4 by the network administrator.

  B.  Subnet Mask: Enter the Subnet of the network.

  C.  Gateway: Enter the TCP/IP gateway of the network access point (router) being used. 

    Gateway configuration is required to properly receive emails from the device.

  D.  HTTP Port: Enter the HTTP port number assigned to the NetWaySP4 module by the network 

    administrator to allow remote access and monitoring. The default inbound port setting is 80. HTTP is not 

    encrypted and unsecure. Even though HTTP can be used for remote access, it is recommended primarily 

    for use with LAN connections.

  E.  HTTPS Port: Enter the HTTPS port number assigned to the NetWaySP4 module by the network 

    administrator to allow remote access and monitoring. The default inbound port setting is 443. 

    Being encrypted and more secure, HTTPS is highly recommended for remote access.

  F.  Click the button labeled 

Submit Network Settings

    A dialog box will display “New network settings will take effect after the server is rebooted”. Click 

OK

.

DHCP:

  A.  After selecting DHCP in the IP Address Method field click the button labeled 

Submit Network Settings

    A dialog box will display “New network settings will take effect after the server is rebooted”. Click 

OK

    Next, click on the button labeled 

Reboot Server

. After rebooting the NetWaySP4 will be set in the DHCP 

    mode. The IP address will be assigned by the router when the NetWaySP4 is connected to the network. 

    It is recommended to have the assigned IP Address reserved to ensure continued access 

    (see the network administrator). 

  B.  Subnet Mask: When operating in DHCP, the router will assign the subnet mask values.

  C.  Gateway: Enter the TCP/IP gateway of the network access point (router) being used.

  D.  HTTP Port: Enter the HTTP port number assigned to the NetWaySP4 module by the network administrator 

    to allow remote access and monitoring. The default inbound port setting is 80. HTTP is not encrypted and 

    unsecure. Even though HTTP can be used for remote access, it is recommended primarily for use with 

    LAN connections. 

Summary of Contents for NetWaySP4

















Reviews: