- 4 -
HubSat4D
3. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 5a, pg. 6) power
LEDs (Green) of the HubSat will illuminate when AC power is present (Fig. 1e, pg. 4) and HubWayAv, HubWayDv
or HubWayDvi Video Balun/Combiner LEDs will illuminate indicating power is present (Fig. 2b, 2d, pg. 6).
4. Measure the output voltage at each Video Balun/Combiner (Figs. 2b, 2d, pg. 6) before making connections to
each camera to insure proper operation and avoid possible damage.
5. Set illuminated master power disconnect circuit breaker to the (OFF) position (Fig. 5a, pg. 6).
6. Connect power outputs of HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners to power
inputs of cameras (Figs. 2a-2e, pg. 5-6). Polarity must be observed.
• HubWayAv/HubWayAv2 - Terminals marked [AC POWER] (Figs. 2a, 2b, 2e, pg. 5-6).
• HubWayDv/HubWayDvi - Terminals marked [– 12VDC +] (Figs. 2c, 2d, pg. 5).
7. Connect the terminals marked [+ DATA -- ] of HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video
Balun/Combiners to data input terminals of cameras for PTZ control (Figs. 2b-2d, pg. 5). Polarity must be observed.
When using fixed cameras disregard this step.
8. Connect the BNC connector of HubWayAv, HubWayAv2, HubWayDv or HubWayDvi Video Balun/Combiners to
the BNC video outputs of cameras (Figs. 2a-2e, pg. 5-6).
9. Set illuminated master power disconnect circuit breaker to the RESET (ON) position (Fig. 5a, pg. 6).
10. The power LEDs (Green) of the HubSat will illuminate when AC power is present (Fig. 1e, pg. 4).
Note: If any of the power LEDs are not illuminated the cause may be due to the following:
a. AC mains fail.
b. Illuminated master power disconnect circuit breaker is tripped.
c. One or both primary in-line fuse(s) are blown.
Note: Replace fuse with same type and rating:
Primary in-line fuses are rated @ 3.5A/250V (Fig. 5b, pg. 6).
d. An individual power output voltage switch is set to the OFF position (Fig. 1d, pg. 4).
e. A PTC is tripped due to a short circuit or overload condition for one or more channels/power outputs.
To reset the PTC:
Fig. 1 - HubSat Circuit Board
PVD1
VIDEO1
VIDEO2
VIDEO3
VIDEO4
PVD2
PVD3
PVD4
+ DA
TA
-
DATA 1-4
VIDEO 1-4
28VAC
24VAC
28VAC
24VAC
28VAC
24VAC
28VAC
24VAC
OF
F
OF
F
OF
F
OF
F
AUX1
AUX2
AUX3
AUX4
1a -
BNC Connector: Video in from remote camera
video out to DVR.
1b -
Output PTCs: Protects each output.
1c -
Power Terminals: 24VAC/28VAC power outputs.
1d -
Output Voltage Switches: Selects 24VAC/28VAC/
OFF for each output.
1e -
LED(s) 1-4: Power output indicators.
1f -
Data: RS422/RS485 input from head end equipment
(DVR) for PTZ control.
1g -
Channels 1-4: Single CAT-5 or higher structured
cable out to HubWay, HubWayLD or HubWayLDH
enables transmission of up to four (4) video signals.
Pin out configuration (Fig. 4, pg. 6).
1h -
Data: CAT-5 or higher structured cable to data port
on HubWay, HubWayLD or HubWayLDH or head end
equipment (DVR).
1i -
Channels 1-4: CAT-5 or higher structured cable
to cameras. Pin out configuration (Fig. 3, pg. 6).
1a
1i
1b
1c
1d
1e
1f
1g
1h
1c
Primary
In-line Fuse
