Overview:
The AL600UL3/AL600UL3X Triple Output Power Supply/Charger is specifically designed for use with access control
and fire-protective signaling systems and accessories. The AL600UL3/AL600UL3X converts a 115VAC 60Hz input into
three (3) outputs (see specifications).
Specifications:
Agency Listings:
•
UL
Listed
for
Access
Control
System
Units
(UL 294) and UL Listed Standard for Safety for Fire
Protective Signaling Systems (UL 1481).
•
cUL
Listed:
CSA Standard C22.2 No.205-M1983,
Signal Equipment.
•
MEA
- NYC
Department
of
Buildings
Approved.
•
CSFM
- California
State
Fire
Marshal
Approved.
•
NFPA
72
compliant
(Fire-Protective
Signaling
Service).
Input:
•
Input
115VAC
/
60Hz,
3.5
amp.
•
AC
input
and
DC
output
LED
indicators.
Output:
•
Class
2
Rated
power-limited
outputs
(5VDC and 12VDC only).
•
1.75
amp
continuous
supply
current
at
5VDC and 12VDC regulated outputs.
•
3
amp
continuous
supply
current
at
24VDC
(for Fire-Protective Signaling use Special applications).
•
Filtered
and
electronically
regulated
outputs.
100 mV p/p output ripple.
Output
(cont’d.)
:
•
Short
circuit
and
thermal
overload
protection.
Battery Backup
•
Built-in
charger
for
sealed
lead
acid
or
gel
type
batteries.
•
Automatic
switch
over
to
stand-by
battery
when
AC fails.
•
Maximum
charge
current
0.7
amp.
•
Zero
voltage
drop
when
switched
over
to
battery
backup.
Supervision:
•
AC
fail
supervision
(form
“C”
contacts).
•
Low
battery
and
battery
presence
supervision
(form “C” contacts).
Additional Features:
•
Power
supply,
enclosure,
cam
lock
and
battery
leads.
•
Enclosure
accommodates
up
to
two
(2)
7AH
batteries.
Enclosure
dimensions
(H
x
W
x
D):
AL600UL3
13.5”
x
13”
x
3.25”
(342.9mm
x
330.2mm
x
82.55mm)
AL600UL3X
15.5”
x
12”
x
4.5”
(393.7mm
x
304.8mm
x
114.3mm).
Stand-by Specifications
(Current is specified on AL3XB input)
:
Output
4 hr. of Stand-by &
5 Minutes of Alarm
24 hr. of Stand-by &
5 Minutes of Alarm
60 hr. of Stand-by &
5 Minutes of Alarm
5VDC - 1.75 amp
5VDC - 0.3 amp
5VDC - 0.1 amp
24VDC / 40AH Battery
12VDC - 1.75 amp
12VDC - 0.3 amp
12VDC - 0.1 amp
24VDC - 3 amp
24VDC - 0.3 amp
24VDC - 0.1 amp
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all local
codes and authorities having jurisdiction. Product is intended for indoor use only.
1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws; level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pgs. 7-8).
Secure enclosure to earth ground. It is recommended to first review the following tables for screw terminals, switch
selection and LED status indications. This will greatly facilitate installation hook-up.
Carefully review:
Stand-by Specifications
(pg. 2)
LED Diagnostics
(pg. 4)
Terminal Identification Table
(pg. 4)
2. Connect AC power (115VAC 60Hz) to the terminals marked [L, N] (Fig. 1, pg. 3). Use 14 AWG or larger for all
power connections (Battery, DC output, AC input). Use 22 AWG to 18 AWG for power-limited circuits
(AC Fail/Low Battery reporting).
Keep power-limited wiring separate from non power-limited wiring (115VAC / 60Hz Input, Battery Wires).
Minimum 0.25” spacing must be provided.
For Fire Alarm applications the outputs are “Special Applications” only, see list (refer to Appendix A, pg. 5).
3. Measure output voltage before connecting devices. This helps avoiding potential damage.
- 2 -
AL600UL3/AL600UL3X
Available from A1 Security Cameras
www.a1securitycameras.com email: [email protected]
