Altos P550 F4 User Manual Download Page 17

Notices 

Information for your safety and comfort 

 

Safety instructions 

 

Read these instructions carefully. Keep this document for future reference. Follow all 

warnings and instructions marked on the product. 

 

Turning the product off before cleaning 

 

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or 

aerosol cleaners. Use a damp cloth for cleaning. 

 

CAUTION for plug as disconnecting device 

 

Observe the following guidelines when connecting and disconnecting power to the power 

supply unit: 

 

 

Install the power supply unit before connecting the power cord to the AC power outlet. 

 

Unplug the power cord before removing the power supply unit from the computer. 

 

If the system has multiple sources of power, disconnect power from the system by 

unplugging all power cords from the power supplies. 

 

CAUTION for accessibility 

 

Be sure that the power outlet you plug the power cord into is easily accessible and located 

as close to the equipment operator as possible. When you need to disconnect power to 

the equipment, be sure to unplug the power cord from the electrical outlet. 

 

Warnings 

 

 

Do not use this product near water. 

 

Do not place this product on an unstable cart, stand or table. If the product falls, it 

could be seriously damaged. 

 

Slots and openings are provided for ventilation to ensure reliable operation of the 

product and to protect it from overheating. These openings must not be blocked or 

covered. The openings should never be blocked by placing the product on a bed, 

sofa, rug or other similar surface. This product should never be placed near or over a 

radiator or heat register, or in a built-in installation unless proper ventilation is 

Summary of Contents for P550 F4

























Reviews: