3. CONTROL ELEMENTS
SPO
TLIGHT
3. CONTROL ELEMENTS
Rear Panel
18 Input Connectors
The input connectors are supplied with XLR and 1/4" TRS jack, it is used to
input the signal.
Standard IEC receptacle. Connect your
to the AC with the
supplied AC power cord. Before powering up your
for the
first time, make certain the stated power requirement of the unit matches the
voltage supplied by the AC socket.
LTO MONITOR
LTO MONITOR
If the fuse blows, replaced with a fuse of the correct type only.
17 AC Inlet and Fuse Holder
19 Output Connectors
The output connectors are supplied with XLR and 1/4" TRS jack, it is used to
output the signal.
SLEEVE/PIN 1
RING/PIN 3
TIP/PIN 2
INPUT
TIP/PIN 2
RING/PIN 3
SLEEVE/PIN 1
AC INPUT
95-120V
/210-240V
60-50Hz
Rated Power Consumption 8W
FUSE:
210-240V: T200mAL 250VAC
95-120V: T315mA 250VAC
REPLACE FUSE WITH CORRECT
TYPE ONLY
Apparaten skall anslutas till
jordat uttag nar den ansluts
till ett natverk
OUTPUT
INPUT
17
18
19
3. CONTROL ELEMENTS
4. APPLICATION IN MONITOR SYSTEM
Output
Monitor AMP Input
Input
SLEEVE/PIN 1
RING/PIN 3
TIP/PIN 2
INPUT
TIP/PIN 2
RING/PIN 3
SLEEVE/PIN 1
AC INPUT
95-120V
/210-240V
60-50Hz
Rated Power Consumption 8W
FUSE:
210-240V: T200mAL 250VAC
95-120V: T315mA 250VAC
REPLACE FUSE WITH CORRECT
TYPE ONLY
Apparaten skall anslutas till
jordat uttag nar den ansluts
till ett natverk
OUTPUT
INPUT
Monitor AMP Output
AUX Send
MIC level signal
Monitor Speaker
4
5
3. CONTROL ELEMENTS
5. INSTALLATION AND CONNECTION
5.1 Mains Connection
Please ensure that the
is set to the correct supply voltage before
plugging the power cord into the wall outlet, use the same fuse as marked on
the fuse holder at the AC power connection. The mains connection of the
is made by using the enclosed mains cord and a standard IEC receptacle.
It meets all of the international safety certification requirements.
LTO MONITOR
LTO
MONITOR
5.2 Audio Connection
The
presents with balanced XLR&1/4" TRS
It
can be interfaced in several ways to support a variety of applications without
any signal loss. The
can be used on a single instrument by
connecting to the mixing console's main inserts, or on an entire mix "in-line" between
a mixing console's outputs and a power amplifier. The defective wiring may degrade
the performance of
, so please use good quality screened audio
cables only. Please follow the guide below to interface
without
experiencing any noise or signal loss.
LTO MONITOR
connectors.
LTO MONITOR
LTO MONITOR
LTO MONITOR
Ok, you have got to this point and you are now in the position to operate your
successfully. However, we advise you to read carefully the
following section to be the real master of your own unit. Not paying attention
enough to the input signal level, to the routing of the signal and the assignment
of the signal will result in unwanted distortion, a corrupted signal or no sound
at all. So you should follow these procedures for every single channel:
LTO MONITOR
Strain Clamp
Sleeve
Tip
Ring
Sleeve=Ground/Screen
Ring=Right Signal
Tip=Left Signal
Use for Headphone
1/4" Stereo (TRS) Jack Plug
Strain Clamp
Sleeve
Tip
Sleeve=Ground/Screen
Tip=Signal
Use for Mono Line In, Mono 1/4" Jack Plugs
1/4" Mono (TS) Jack Plug
D1
500W 2
(dB)
12
16
18
20
22
24
26
28
30
6
CH1
(dB)
12
16
18
20
22
24
26
28
30
6
CH2
SIG CLIP PROT
SIG CLIP PROT