7.TECHNICAL SPECIFICATIONS
Input Channel
Digital Input Gain
/+ 12 dB / step 0.5 dB
4 Parametric Filters
Gain
/+ 15 dB / step 0.5 dB
Freq 20 Hz
20 KHz step 1/12 oct
BandWidth 0.05 oct
3 oct / step 0.05 oct
Delay line
Up to 512 ms minimum step 21us
Output Channel
Digital Out Volume
/+ 12 dB / step 0.5 dB
Delay line
Up to 512 ms minimum step 21us
5 Parametric Filters
Gain
/+ 15 dB / step 0.5dB
Freq 20 Hz - 20 KHz / step 1/12 oct
BandWidth 0.05 oct - 3 oct step 0.05 oct
High Pass Filter Type Butterworth
Freq: 20 Hz - 20 KHz / step 1/12 oct
Slope: Bypass, 1 ord, 2 ord, 3 ord, 4 ord
st
nd
rd
th
Low Pass Filter Type Butterworth
Freq:20 Hz - 20 KHz / step 1/12 oct
Polarity
Phase 0 or 180
Limiter
Threshold
29 dB up to 0 dB / step 1dB
Release Time 0.4 s, 0.5 s, 0.7 s, 1.4 s
Attack Time 0.05 s, 0.10 s, 0.20 s, 0.30 s
Slope: Bypass, 1 ord, 2 ord, 3 ord, 4 ord
st
nd
rd
th
16
Memory
1 Factory Preset
64 User Preset
Digital
Processor speed
36 MIPs
DSP resolution
24
32 bits
Control
Microprocessor
MIDI section
Connections
Input/output/thru
Sockets
5
poles DIN(female)
Photocoupled
Mode
Analog
Input Impedance
>40k
Output Impedance
<200
Input MAX Level
12dBv
Output MAX Level
12dBv
20BITS Sigma-Delta
A/D Converter
D A
/ Converter
24BITS Sigma-Delta
Performance
THD+N
0.02
(1KHz
3dBFS)
Amplitude Response
20Hz
20KHz
S/N Ratio
>97dBa
The Whole Unit
3.2 The Rear Panel
Inputs (14)
Outputs (15)
MIDI Connectors (16)
-MIDI in: 5-poles DIN connector for the MIDI input to the
LTO DRIVE2.3.
-MIDI thr: 5-poles DIN connector for the MIDI thr.
-MIDI out: 5-poles DIN connector for the MIDI output f om the
LTO DRIVE2.3.
r
Power Connector (17)
This is an IEC 3-pole socket for connecting the AC power supply to the
LTO DRIVE2.3.
4.INSTALLATION & CONNECTION
Power SW with LED (1)
Turns the apparatus on and off. Press this SW, the power LED inside the SW will turn on.
Dial Control knob (5)
Used to change editable values.
14.Input Connector for Input1 and Input2
15.Output Connector for Output1~Output4
16.MIDI Connector
17.Power Connector
4.1 Power Up and Audio Connections
a. Audio Connections
b. Power Up Setting
Do not bundle audio cables with AC power cords.
formers, monitors, computers, etc.
Always unplug cables by firmly grasping the body of the plug and pulling directly outward.
Do not place cables where they can be stepped on.
Avoid twisting a cable or having it make sharp, right angle turns.
Before turning on the
LTO DRIVE2.3's power, check if:
All connections have been made correctly.
The volume controls of the amplifier or mixer are turned down.
5
16
15
14
into an AC outlet.
Turn on the power of the
LTO DRIVE2.3, pushing the ON/OFF button on the front panel.
Turn on the power of the amplifier/mixer, and adjust the volume.
17
2 XLR - F (BAL)
4 XLR - M (BAL)
Inputs
Outputs
These are XLR balanced connectors which connect to sources such as the channel inserts on mixing consoles.
They may be used with nominal input levels from consumer to professional audio.
LTO DRIVE2.3 has 4 outputs, they are XLR balanced connectors which connect to devices such as the channel
inserts on mixing console or power amplifier inputs .
The connections between the
LTO DRIVE2.3 and the other audio devices have to be made using high quality
cables so to prevent bad performances of the
LTO DRIVE2.3 itself. So it should be good to use low-capacitance
shielded cables with a flexible internal conductor. Connect the cables to the
LTO DRIVE2.3 properly by obser-
ving the following precautions:
Do not place audio cables and
LTO DRIVE2.3 near sources of electromagnetic interference such as trans-
Insert the Power plug into the POWER input on the rear panel of the
LTO DRIVE2.3 and plug the power cord
INPUT1
INPUT2
OUTPUT1
OUTPUT2
OUTPUT3
OUTPUT4
INPUT
THRU
OUTPUT
MIDI
SERIAL
MODEL
CODE
AC INPUT
95-240V
60-50Hz
Rated Power Consumption 15W
FUSE:
210-240V: T315mAL 250VAC
95-120V: 500mA 250VAC
REPLACE FUSE WITH CORRECT
TYPE ONLY
Apparaten skall anslutas till
jordat uttag nar den ansluts
till ett natverk
A102
PUSH
2
1
3
NEW
TIDE
PUSH
2
1
3
NEW
TIDE