Alto 3DS Operator'S Manual Download Page 4

Page 4

AMERICAN SANDERS TECHNOLOGY Operator’s Manual - 3DS

DANGER:

To avoid injury keep hands, feet, and loose clothing away from all moving parts on the
machine.  Disconnect the power cord before replacing the pad, changing the abrasive, or
when servicing.  Do not operate the machine unless all guards are in place.  Never leave
the machine unattended while connected to a power source.

WARNING:

Shock hazard.  Electrical components of this machine can “short-out” if exposed to water
or moisture.  Keep the electrical components of the machine dry.  Wipe the machine down
after each use.  For storage, keep the machine in a dry building.

WARNING:

Injury can occur if protective clothing or equipment is not used while sanding.  Always wear
safety goggles, protective clothing, and dust mask while sanding.

WARNING:

Any alterations or modifications of  this machine could result in damage to the machine or
injury to the operator or other bystanders.  Alterations or modifications not authorized by the
manufacturer voids any and all warranties and liabilities.

WARNING:

Operating a machine without observing all labels and instructional information could result
in injury to the operator or damage to the machine.  Read all machine labels before
attempting to operate the machine.  Make sure all of the labels and instructional information
are attached or fastened to the machine.  Get replacement labels and decals from your
authorized distributor.

WARNING:

The machine is heavy.  Injury could occur  to the operator or other bystanders unless proper
lifting procedures are used.  Get help to lift the machine.

Explanation of Hazard Symbols

 

Failure to read operator’s manual could result in injury to operator or damage to

       machine.

The symbol of a flame shows that the material can ignite and burn you.

The symbol of a man with voltage going through him depicts electrocution
or shock.  This can cause death or severe injury.

This symbol refers to the danger of moving parts. Injury can occur.

This symbol of a person wearing goggles warns of injuries to eyes.

This symbol  of a man lifting shows that injury could occur without proper
lifting procedures.

Explosion

Electrical Shock

Moving parts

Eye Protection

Heavy Object

Read Owner’s Manual

Summary of Contents for 3DS












Reviews: