TP115-110/
Computer/Component AV Twisted Pair Transmitter
User’s Guide
400-0431-008
1
Welcome!
We greatly appreciate your purchase of the TP115-110 Computer/Component
Video + Audio Twisted Pair Transmitter. We are sure you will find it reliable
and simple to use. Superior performance for the right price, backed by solid
technical and customer support is what ALTINEX has to offer.
We are committed to providing our customers with Signal Management
Solutions
®
to the most demanding audiovisual installations at very competitive
pricing and we welcome you to join the ranks of our many satisfied customers
throughout the world.
1. Precautions and Safety Warnings
Please read this manual carefully before using your TP115-110. Keep this
manual handy for future reference. These safety instructions are to ensure the
long life of your TP115-110 and to prevent fire and shock hazards. Please read
them carefully and heed all warnings.
1.1 General
Qualified ALTINEX service personnel or their authorized representatives
must perform all service.
1.2 Installation Precautions
To prevent fire or shock, do not expose this unit to water or moisture.
Do not place the TP115-110 in direct sunlight, near heaters or
heat-radiating appliances, or near any liquid. Exposure to direct sunlight,
smoke, or steam can harm internal components.
Handle the TP115-110 carefully. Dropping or jarring can damage the
unit.
Do not pull any cables that are attached to the TP115-110.
1.3 Cleaning
Clean only with a dry cloth. Never use strong detergents or solvents such
as alcohol or thinner. Do not use a wet cloth or water to clean the unit.
Do not open the unit to clean.
1.4 FCC Notice
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions found herein, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Any changes or modifications to the unit not expressly approved by
ALTINEX, Inc. could void the user’s authority to operate the equipment.
2. Installation Procedures
Step 1.
Determine the best location for the TP115-110 and TP115-111. Where possible, locate the TP115-110 as close to the video source as possible and the
TP115-111 as close to the receiving component as feasible.
Step 2.
Apply power to the TP115-110 using the power adaptor provided. The Power LED should be on and red.
Step 3.
Connect the video source to the input of the TP115-110 using a high quality video cable.
Step 4.
The Power LED should change from red to green indicating a signal is present.
Step 5.
Connect the audio input source to the audio jack on the TP115-110.
Step 6.
Run a CAT-5 cable from the 4TP Output of the TP115-110 to the 4TP Input on the TP115-111.
NOTE: Ensure good signal transmission by routing the cable avoiding any sharp angles, creases, or bends.
Step 7.
Connect the TP115-111 video and audio outputs to their receiving devices.
NOTE: The L+, L- and GND outputs on the TP115-111 terminal block output contain the mono audio output signal. The R+ and R- pins are
not used.
Step 8.
Apply power to the TP115-111 using the power adaptor provided. The Power LED should be on and red; green if a signal is present.
Step 9.
The units are now operational.
3. Limited Warranty/Return Policies
Please see the ALTINEX website at
www.altinex.com
for details on warranty and return policies.
