TNP600
TNP600
TNP600
TNP600//// C
C
C
Customizable
ustomizable
ustomizable
ustomizable T
T
T
Tilt
ilt
ilt
ilt ‘N P
‘N P
‘N P
‘N Plug
lug
lug
lug
®
®
®
®
User’s Guide
400-0493-002
1
Welcome!
We greatly appreciate your purchase of the TNP600 Customizable
TILT ‘N PLUG
®
. We are sure you will find it reliable and simple to use.
Superior performance for the right price, backed by solid technical and
customer support is what ALTINEX has to offer.
We are committed to providing our customers with
Signal Management Solutions
®
to the most demanding audiovisual
installations at very competitive pricing and we welcome you to join the
ranks of our many satisfied customers throughout the world.
1. Precautions and Safety Warnings
Please read this manual carefully before using your TNP600. Keep this
manual handy for future reference. These safety instructions are to ensure
the long life of your TNP600 and to prevent fire and shock hazards. Please
read them carefully and heed all warnings.
1.1 General
•
Unauthorized personnel shall not open the unit, as there are
high-voltage components inside.
•
Qualified ALTINEX service personnel or their authorized
representatives must perform all service.
1.2 Installation Precautions
•
For best results, place the TNP600 in a dry area away from dust.
•
To prevent fire or shock, do not expose this unit to water or moisture.
Do not place the TNP600 in direct sunlight, near heaters or heat
radiating appliances, or near any liquid. Exposure to direct sunlight,
smoke, or steam can harm internal components.
•
Handle the TNP600 carefully. Dropping or jarring can damage the
bezel.
•
Never place fingers inside the opening on either side of the unit. This
action could cause injury due to sharp edges inside.
•
Do not place heavy objects on top of the TNP600. Do not use excessive
force to push down on the top of the unit.
•
Disconnect the TNP600’s power cord to turn off the main power. This
supplies power to the power socket on the pop up panel. The power
outlet should be installed near the equipment and be easily accessible.
•
We recommend using wall outlets with a Ground Fault Circuit
Interrupter (GFCI) for maximum protection.
•
Install all cables according to the instructions found herein. Do not
force or pull out any cable or power cord attached to the TNP600.
1.3 Cleaning
•
Surfaces should be cleaned with a dry cloth. Never use strong
detergents or solvents such as alcohol or thinner. Do not use a wet cloth
or water to clean the unit.
1.4 FCC Notice
•
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
•
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions found herein, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his expense.
•
Any changes or modifications to the unit not expressly approved by
ALTINEX, Inc. could void the user’s authority to operate the
equipment.
2. Installation Procedures
Step 1.
Cut an opening into the table’s surface. Refer to the ALTINEX website at www.altinex.com for table cutout requirements.
Note: The table can be 2.50” or less in thickness. Always confirm dimensions before cutting to insure that specifications have not changed.
Step 2.
Insert the TNP600 into the table cutout.
Step 3.
Place the support brackets under the table and place them between the support mount grooves on the side of the TNP600. Attach the brackets to the
groove at the desired height and secure them to the bottom of the table using the thumbscrews provided.
Step 4.
To lower the unit, push on the top of the TNP600 until it locks into place.
Note: A standard, empty, TNP600 does not latch in the down position. A cable support bracket is required. The exact cable support bracket required
is determined at the time of customization.
If Custom Plates Are Installed
Step 5.
Secure all cables to the underside of the table using the cable clamps and screws included with the TNP600. Pass the power cord from the bottom of
the housing and attach it to the table separate from the signal cables.
Leave enough slack in the service loop to allow for easy opening and closing, but not too much as to cause excess drooping of the service loop.
Step 6.
Connect the appropriate cables with the correct input connectors on the bottom of the unit.
Step 7.
Once you have applied power and connected the proper cables on the bottom of the unit you may raise the unit. To raise the TNP600 into position,
push down on the front of the top cover; the latching mechanism will then release, allowing the pneumatic spring to raise it into position.
Note: It may be necessary to adjust the service loop of the cables for optimal performance.
3. Limited Warranty/Return policies
Please see the ALTINEX website at www.altinex.com for details on warranty and return policies.
