background image

SWITCHERS

400-0099-003

3

ABOUT YOUR MX2456RM

2

MX2456RM

6-IN, 1-OUT VIDEO/AUDIO SWITCHER

The 

MX2456 RM 

is a video and audio switcher with 

six video inputs that can be connected to a single 
video output and has six balanced-stereo audio 
inputs. These six balanced-stereo audio inputs can 
be connected to a singe balanced-stereo audio 
output.  This allows for the non-simultaneous 
connection of up six computers or six video and six 
audio sources to a monitor or projector and to any 
audio system. 

The 

MX2456RM

can pass a variety of video signal 

types: RGBHV, RGBS, RGsB, Component Video 
(Y, R-Y, B-Y), S-Video and Composite Video. The 

MX2456RM

is controllable by using its built-in front 

panel or through RS-232. 

Each of the video inputs is ground loop isolated and 
can  promote individual equalization of video gain 
according to different cable lengths. 

The 

MX2456RM

has a video bandwidth of 300 MHz 

and an audio bandwidth of 40 kHz.

TECHNICAL SPECIFICATION

3

FEATURES/ 
DESCRIPTION

Audio

RGBHV

GENERAL
Inputs

6

6

Input 
Connector

5-pin term. blocks

15-pin HD female

Outputs

1

1

Output 
Connector

5-pin term. blocks

BNC female

Compatibility

Balanced audio

VGA, RGBHV, 

RGBS,RGsB, & 

C-Video              

(Y, R-Y, B-Y)

Table 1.

MX2456RM

General

MECHANICAL

MX2456RM

Width (inches)

1.75in (44mm)

Height (inches)

17.00 in (432mm)

Depth (inches)

9.00in (229mm)

Weight (pounds)

5lbs (2.28kg)

Finish

Gray

Front/Rear Panel

Lexan

T° Maximum

50°C

Humidity

90% non-condensing

MTBF (calculations)

40,000 hrs (min)

Table 2. 

MX2456RM

Mechanical

ELECTRICAL

Audio 

RGBHV

Input Signal

Differential

1.8V p-p

-

Analog

-

1.2V p-p

Composite Video

-

-

Impedance

10 k Ohms

75 Ohms

CMRR

80dB @ 10 Hz to 

20k Hz

-

Input Sync Signals

Composite, 
Horizontal, &  
Vertical

-

TTL (+/-)

Output Signals

Analog

-

1.2V p-p

Fall/ Rise Time

-

less than 2.4ns 

Impedance

600 Ohms

75 Ohms

Crosstalk

80 dB @ 1kHz

-48dB @ 10 MHz

Differential

1.8Vp-p

-

Signal to Noise 
Ratio

More than 95 dB

-

Bandwidth

10 Hz – 40 kHz

300MHz

Stereo Signal 
Separation

More than 60dB 

@ 20 kHz

-

Output Sync Signals

Impedance

-

22 Ohms

Power

External Power

90V AC to 260V 

AC 50/60Hz

Power 
Consumption

14 watts max.

Table 3. 

MX2456RM

Electrical

Summary of Contents for MX2456RM
















Reviews: