Altinex MULTI-TASKER MT104-107 User Manual Download Page 3

                                                         MULTI-TASKER

2

PRECAUTIONS / SAFETY WARNINGS

1

Please read this manual carefully before using
your 

MT104-107

. Keep this manual handy for

future reference. These safety instructions are to
ensure the long life of your 

MT104-107 

and to

prevent fire and shock hazard. Please read them
carefully and heed all warnings.

1.1  GENERAL

 Qualified ALTINEX service personnel, or their

authorized representatives must perform all
service.

1.2  INSTALLATION

 To prevent fire or shock, do not expose this unit

to rain or moisture. Do not place the 

MT104-107

in direct sunlight, near heaters or heat radiating
appliances, or near any liquid. Exposure to
direct sunlight, smoke, or steam can harm
internal components.

 Do not pull the cables that are attached to the

MT104-107

.

 Insert the card carefully into the slots of the

Multi-Tasker™ without bending any edges.

 When removing a card, please make sure that

the card to which it is attached is also pulled out
simultaneously.

1.3  CLEANING

 Clean only the connector area with a dry cloth.

Never use strong detergents or solvents, such
as alcohol or thinner. Do not use a wet cloth or
water to clean the card. Do not clean or touch
any component or PCB.

1.4  FCC / CE NOTICE

 This device complies with part 15 of the FCC

Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.

 This equipment has been tested and found to

comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable
protection against harmful interference when
the equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.

 Any changes or modifications to the unit not

expressly approved by ALTINEX, Inc. could void
the user’s authority to operate the equipment.

Summary of Contents for MULTI-TASKER MT104-107














Reviews: