Altimium PWSU12 User Manual Download Page 12

Page: 12 / 28

Integrated Switching Power Supply

Altimium 4 www.altimium.com

3. System Connection

3.1 Usage Precautions



System should be installed in a clean environment and has a prop temperature
and humidity.



All of the power switches, plugs, sockets and power cords should be insulated and
safe.



All devices should be connected before power on.

3.2 System Diagram

3.3 Connection Procedure

Step1.

Connect the devices needed to be powered to the DC ports on rear panel.

Step2.

Connect the PC to the RS232 port on rear panel.

Step3.

Connect the PC to the TCP/IP port on the rear panel.

Step4.

Connect the power cables to the one or both of AC1 and AC2 input port.

AC100V 240V

RS232

TCP IP

24V

AC100V 240V

AC1

AC2

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

24V

12V

SELECT

Powered Device 1

Powered Device 2

Powered Device 3

100~240VAC

RS232 Control

TCP IP Control

Power Supply

Summary of Contents for PWSU12




























Search results

Summary of Contents for PWSU12

Reviews:

Related manuals for PWSU12

Brands by name

Popular brands

Altimium PWSU12, User Manual

Search results

Summary of Contents for PWSU12

Reviews:

Related manuals for PWSU12

Brands by name

Popular brands