manualshive.com logo in svg

Altera Stratix V Hard IP, User Manual, Page: 14 / 232

Share
Download
Altera Stratix V Hard IP User Manual Download Page 14

1–6

Chapter 1: Datasheet

Debug Features

Stratix V Hard IP for PCI Express

June  2012

Altera Corporation

User Guide

Figure 1–2

 illustrates a Stratix V that includes the following components:

■

A Root Port that connects directly to a second FPGA that includes an Endpoint.

■

Two Endpoints that connects to a PCIe switch.

■

A host CPU that implements CvP using the PCI Express link connects through the 
switch. For more information about configuration over a PCI Express link, refer to 

“Configuration via Protocol (CvP)” on page 10–1

. 

Debug Features

The Stratix V Hard IP for PCI Express includes debug features that allow observation 
and control of the Hard IP for faster debugging of system-level problems. For more 
information about debugging refer to 

Chapter 16, Debugging

.

IP Core Verification

To ensure compliance with the PCI Express specification, Altera performs extensive 
validation of the Stratix V Hard IP Core for PCI Express. 

Altera’s simulation environment uses multiple testbenches that consist of 
industry-standard BFMs driving the PCI Express link interface. 

Figure 1–2. PCI Express Application Including Stratix V using Configuration via Protocol

PCIe Link

PCIe Hard IP

RP

Switch

PCIe

Hard IP

RP

User Application

Logic

PCIe Hard IP

EP

PCIe Link

PCIe Link

User Application

Logic

Stratix V with Hard IP for PCI Express

Stratix V with Hard IP for PCI Express

Active Serial or 

Active Quad 

Device Configuration

Configuration via Protocol (CvP)

using the PCI Express Link

Serial or

Quad Flash

USB

Download 

cable

PCIe

Hard IP

EP

User 

Application

 Logic

Stratix V with Hard IP for PCI Express

Config 
Control

CVP

USB 

Host CPU

PCIe

Summary of Contents for Stratix V Hard IP









































































































































































































































Reviews:

No comments