Altera Stratix III Using Manual Download Page 53 | Manualshive

Page: 53 / 59

background image

Example Project Walkthrough

Page 53

© November 2008

Altera Corporation

AN 436: Using DDR3 SDRAM in Stratix III and Stratix IV Devices

Finally, the loading seen by the FPGA during writes to the memory is different
between a system using DIMMs versus a system using components. The additional
loading from the DIMM connector can reduce the edge rates of the signals arriving at
the memory thus affecting available timing margin.

f

For more information about Stratix III devices signal integrity, refer to

www.altera.com/technology/signal/devices/stratix3/sgl-stratix3.html

.

Adjust Drive Strength

Due to the loading of the line, the Quartus II software may report that the default or
chosen drive strength cannot drive the line to the specified toggle rate or minimum
pulse width, as shown in

. If you encounter this error, use the stronger drive

strength I/O standard. Ensure that you re-simulate your design with the new drive
strength to ensure that signal quality is still acceptable.

1

The Quartus II software v8.1 has a bug that results in an incorrect calculation for the
toggle rate for differential I/O standards.

Verifying Design on a Board

The SignalTap II logic analyzer shows read and write activity in the system.

f

For more information on using the SignalTap II logic analyzer, refer to the following
documents:

■

Design Debugging Using the SignalTap II Embedded Logic Analyzer

Quartus II Handbook

Figure 24.

Minimum Pulse Width Error

«
...
51
52
53
54
55
...
»

Summary of Contents for Stratix III




























































Reviews:

No comments

Related manuals for Stratix III

Brand: Daikin Pages: 48

Brand: Daikin Pages: 77

Brand: Daikin Pages: 32

Brand: Daikin Pages: 14

Brand: Daikin Pages: 16

Brand: Daikin Pages: 1

Brand: Danfoss Pages: 16

Brand: H3C Pages: 69

Brand: FAAC Pages: 44

iBox Hub 25020180

Brand: Hans Grohe Pages: 36

Brand: V2 Pages: 12

Brand: H3C Pages: 5

Brand: z21 Pages: 2

Brand: Auber Pages: 3

Brand: Atari Pages: 3

Brand: Woodward Pages: 32

Controller CR100

Brand: Sonos Pages: 2

NetLinx Integrated Controller NI-3100

Brand: AMX Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands