Altera Stratix III Using Manual Download Page 5

Page: 5 / 59

Background

Page 5

Altera Corporation

AN 436: Using DDR3 SDRAM in Stratix III and Stratix IV Devices

■

Differential DQS mode

■

Read and write leveling circuitry

■

Dynamic on-chip termination (OCT) control

To use these features you should use the Altera DDR3 SDRAM high-performance
controller (a complete solution) or the Altera ALTMEMPHY megafunction (for a fully
configured PHY that requires an additional custom or third-party memory controller).

Alternatively, you may access these IOE features directly via the following low-level
megafunctions:

■

ALTDQ_DQS megafunction—allows you to parameterize the following features:

■

DDR

■

alignment and synchronization

■

half data rate

■

DQS mode

■

ALTDLL megafunction—allows you to parameterize the DQS phase-shift circuitry

■

ALTOCT megafunction—allows you to parameterize the IOE OCT features

■

ALTPLL megafunction—allows you to parameterize the device PLL

■

ALTIOBUF megafunction—allows you to parameterize the device IO

Device Pin Utilization

Table 3

shows the DDR3 SDRAM interface pins and how to connect them to Stratix III

pins.

Table 3.

Stratix III DDR3 SDRAM Interface Pin Utilization

(Part 1 of 2)

Pin

Pin Planner Symbol

Stratix III Pin

mem_dq

mem_dm

within the respective DQ group. Each DQ group has a

common background color for all of the associated

and

pins.

Differential

mem_dqs

mem_dqsn

S or Sbar

DQS

DQSn

mem_clk[0]

mem_clk_n[0]

—

Any unused

DQS

pins with

DIFFIO_RX

capability.

(1)

mem_clk[n:1]

mem_clk_n[n:1]

—

Any unused

DQS

pins with

DIFFOUT

capability

(where n is greater than or equal to 1).

ALTMEMPHY-based solutions support only single rank
designs:

■

Only the first rank is initialized (other ranks may have
a different CAC mapping in DDR3 SDRAM).

■

Only the first rank is calibrated to, so exact timing
requirements for other ranks may be different.

Summary of Contents for Stratix III




























































Search results

Summary of Contents for Stratix III

Reviews:

Related manuals for Stratix III

Brands by name

Popular brands

Altera Stratix III, Using Manual

Search results

Summary of Contents for Stratix III

Reviews:

Related manuals for Stratix III

Brands by name

Popular brands