background image

30

RELAY ACTIVE BY PA OUT KEY

SWITCH

 

→ PRESET 1.

LED BLINKING

→ The relay 

 is activated when the PA output 

 is active 

with the PA out 

 switch. 

Factory default.

LED OFF

→ The relay 

 is not activated when the PA output 

 is

active with the PA out 

 switch.

RELAY ACTIVE BY TALK A KEY

SWITCH

 

→ PRESET 2.

LED BLINKING

→ The relay 

 is activated when the microphone of the line 

A is active with the TALK A 

 switch.

LED OFF

→ The relay 

 is not activated when the microphone of the 

line A is active with the TALK A 

 switch. 

Factory default.

TALK KEY MODE

SWITCH

 

→ PRESET 3.

LED BLINKING

→ Push to talk mode, the TALK 

 switch don't have

     latch mode.

LED OFF

→ Latch in short time presses of the switch and push to talk 

in long presses of the switch. 

Factory default.

CALL/TALK KEYS INVERTED FUNCTION

SWITCH

 

→ PRESET 4.

LED BLINKING

→ The Call 

 switch and the talk 

 switch and indicators 

     are inverted in function. Call key becomes Talk key and 
     vice versa.

LED OFF

→ The Call 

 switch and the talk 

 switch and indicators, 

     are working as normal.

Factory default. 

         

CHANGING INVERTED FUNCTION LABELS

.

TALK label. Open the Call lens by pulling it out. Change the included label accordingly.

CALL label. You have to place the included label over the TALK text.

* →  The parameters  “ONLY EF-204 DIRECT ACCESS“,  marked *,  can not be set 
directly on the EF-202 base station, but can be configured via the control software: 
ALTAIR EF-204.

EF-202/EF-204  MASTER STATION - SERIE E-200

11

31

27

9

31

27

9

31

31

11

6

11

12

12

11

Summary of Contents for EF-202



































Reviews: