Waterproof Keypad
AS626S
Read all instructions before starting installation
To set new master code
TAKE TIME TO ALLOW EACH BUTTON INPUT / LED TO REGISTER
Enter
H H
1 2 3 4
H H
The keypad enters programming mode,
the Red LED flashes
Enter
2
The Red LED illuminates for 2 seconds and
then flashes
Enter
0-0-0#
The Red LED illuminates for 2 seconds and
then flashes
Enter
new 4-8 digit code
This is the new master code, record the
number and keep it safe
Enter
#
The Red LED illuminates for 2 seconds and
then flashes
Re-enter
the new master code
The Red LED illuminates for 2 seconds and
then flashes
Enter
#
Enter
#
To exit programming mode
To set a new master code of 112233
Enter
H H
master code
H H
2 000# 112233# 112233# #
To set a new user code
Enter
H H
master code
H H
The keypad enters programming mode,
the Red LED flashes
Enter
2
The Red LED illuminates for 2 seconds and
then flashes
Enter
address of new user code i.e. 001 (001-200 accepted)
Enter
#
The Red LED illuminates for 2 seconds and
then flashes
Enter
new 4-8 digit user code
This is the new user code, record the
number and keep it safe
Enter
#
The Red LED illuminates for 2 seconds and
then flashes
Re-enter
the new 4-8 digit user code The Red LED illuminates for 2 seconds and
then flashes
Enter
#
The new code is added, to add new codes
continue from second step, changing the
address each time. When finished enter an
additional # to exit programming mode.
Re-Enter
2 to set the next code or # to EXIT
To set a new user code of 6626 in address 1
Enter
H H master code H H 2 001# 6626# 6626# #
To set a new user code of 6626 in address 1 & 7788 in address 2
Enter
H H
master code
H H
2 001# 6626# 6626# 2 002# 7788# 7788# #
To remove an individual user code -
Only the user code addresses are
removable, the master code may be changed but not removed
Enter
H H
master code
H H
The keypad enters programming mode,
the Red LED flashes
Enter
3
The Red LED illuminates for 2 seconds and
then flashes
Enter
address of user code to
be removed
Example 001 (001-200 accepted)
Enter
#
The red LED illuminates for 2 seconds and
then flashes (Address accepted)
Enter
address of user code to
be removed
Example 001 (001-200 accepted)
Enter
#
The red LED illuminates for 2 seconds and
then flashes the code is removed
Enter
#
Exit programming mode
To remove all user codes
Enter
H H
master code
H H
The keypad enters programming mode,
the red LED flashes
Enter
4
The Red LED illuminates for 2 seconds and
then flashes
Enter
master code
Enter
#
The Red LED illuminates for 2 seconds and
then flashes 40 sec. All user code addresses
are removed
Enter
#
For exit programming
To set lock open time
Enter
H H
master code
H H
The keypad enters programming mode,
the Red LED flashes
Enter
1
The Red LED illuminates for 2 seconds and
then flashes
Enter
door open time
(01-99) Ex. 05 = 5 seconds
Enter
#
The Red LED illuminates for 2 seconds and
then flashes
Enter
#
For exit programming
To set the door open time to 10 seconds
Enter
H H
master code
H H
1 10 # #
To set output relay to latching mode (On-Off)
Enter
H H
master code
H H
The keypad enters programming mode,
the Red LED flashes
Enter
1
The Red LED illuminates for 2 seconds and
then flashes
Enter
00
Enter
#
The Red LED illuminates for 2 seconds and
then flashes
Enter
#
The relay is set to latching mode
TO PROGRAM THE RELAY FOR A TIMED FUNCTIONING PLEASE PERFORM
PROCEDURE 5.
To set Normally Open
Enter
H H
master code
H H
The keypad enters programming mode,
the Red LED flashes
Enter
6
The red LED illuminates for 2 seconds and
then flashes
Enter
0
Enter
#
The Red LED illuminates for 2 seconds then
flashes
Enter
#
Exit the programming mode
To set Normally Closed
Enter
H H
master code
H H
The keypad enters programming mode,
the Red LED flashes
Enter
6
The red LED illuminates for 2 seconds and
then flashes
Enter
1
Enter
#
The Red LED illuminates for 2 seconds then
flashes
Enter
#
Exit the programming mode
OPERATING THE KEYPAD
Enter
user code #
The relay operates and Green LED
illuminates
If three incorrect attempts are made to enter a user code, the keypad will lock
out for thirty seconds
DATA RESET
There are two basic models out in the field. Before attempting Data Reset identify
the model concerned. Dependent on model select correct reset instructions.
In the event that programming administration is lost, or errors have been made
in the programming, it is possible to set the keypad master back to the factory
default:
Version 1
Power off to keypad - wait 5 seconds - reapply power to Keypad
When power reapplied - if Red LED stays on for 1 second = Version 1
If the unit has been fitted with, this process will destroy the anti-tamper plugs
Remove anit-tamper plugs and the keypad from the wall
Press the reset button on the rear of keypad
The red LED illuminates for 2 seconds and then flashes
Enter
1234#
The red LED illuminates for 2 seconds and a
continuous tone is heard
Press the reset button on the rear of keypad
Enter #
The red LED illuminates for 2 seconds and
then flashes
Enter
#
The relay is set to open the door for 5
seconds
Master code
1-2-3-4
User code
5-6-7-8-9-0
Version 2
Power off to keypad - wait 5 seconds - reapply power to Keypad
When power reapplied - if Red LED stays on for 3 seconds = Version 2
Power up the unit
During the first 3 seconds the Red LED is ON
Enter
**
1234#
Green LED will appear then turn to Red LED
The unit will sound 3 times and the data will
be restored as follows
Master code
1-2-3-4
User code
5-6-7-8-9-0
Please erase this code at address 200
Door open time
5 seconds
Warranty
This product is guaranteed for a period of
5 years
against defects in manufacture,
workmanship or materials provided that all electrical and mechanical installation
requirements are adhered to as per this instruction sheet. All third party and
consequential claims are expressly excluded from this warranty.
1
6
3
4
5
7
8
2
PROGRAMMING THE KEYPAD CONTINUED..
