20
-EN
iDA-X303
iDA-X301/iDA-X301RR
Adjusting Subwoofer/Bass/Treble/
Balance (Between Left and Right)/Fader
(Between Front and Rear)/Loudness/
Defeat
1
Press
IMPRINT
(iDA-X303 only) or
SOUND
(iDA-X301/iDA-X301RR only) repeatedly to choose
the desired mode.
Each press changes the mode as follows:
SUBW LV
*
1
BASS LV
TREBLE LV
BALANCE LV
FADER LV
*
2
LOUD
*
3
DEFEAT
VOLUME
SUBW LV
*
1
Subwoofer: 0 ~ +15
Bass level: –7 ~ +7
Treble level: –7 ~ +7
Balance: –15 ~ +15
Fader: –15 ~ +15
Loudness : ON/OFF
Defeat : ON/OFF
Volume: 0 ~ 35
•
If
IMPRINT
(iDA-X303 only) or
SOUND
(iDA-X301/iDA-X301RR
only) is not pressed within 5 seconds after selecting the Subwoofer,
Bass, Treble, Balance or Fader mode, the unit automatically returns
to normal mode.
•
Loudness introduces a special low-and high-frequency emphasis at
low listening levels. This compensates for the ear’s decreased
sensitivity to bass and treble sound. The function is inoperable when
DEFEAT is set to ON.
*
1
When the subwoofer mode is set to OFF, its level cannot be adjusted.
*
2
If you set the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) switch of
the IMPRINT audio processor (PXA-H100) to 2.2ch (3WAY), you
cannot adjust the FADER mode. For details, refer to the Owner’s
Manual of PXA-H100.
*
3
When an external audio processor is connected, this setting cannot
be made.
2
Turn the
Double Action encoder
(iDA-X303 only)
or
Rotary encoder
(iDA-X301/iDA-X301RR only)
until the desired sound is obtained in each mode.
•
Depending on the connected devices, some functions and display
indications do not work.
Turning Subwoofer ON/OFF
When the subwoofer is on, you can adjust the subwoofer output level
(refer to page 20).
For iDA-X303, the following setting can be made only when the
IMPRINT audio processor (PXA-H100) is not connected.
1
Press and hold
IMPRINT
(iDA-X303 only) or
SOUND
(iDA-X301/iDA-X301RR only) for at least 2
seconds to activate the AUDIO selection mode.
2
Turn the
Double Action encoder
(iDA-X303 only)
or
Rotary encoder
(iDA-X301/iDA-X301RR only) to
select the SUBW mode, and then press
/
ENTER
.
SUBW
SUBW SYSTEM
*
BASS
TREBLE
HPF
SUBW
* Displayed only when subwoofer is ON.
3
Turn the
Double Action encoder
(iDA-X303 only)
or
Rotary encoder
(iDA-X301/iDA-X301RR only) to
select SUBW ON/OFF, and then press
/
ENTER
.
ON
OFF
4
Press
to return to normal mode.
•
If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
•
If
is pressed during setting, the unit returns to the previous item.
Setting the Subwoofer System
When the subwoofer is on, you can select either SYS 1 or SYS 2 for the
desired subwoofer effect.
For iDA-X303, the following setting can be made only when the
IMPRINT audio processor (PXA-H100) is not connected.
1
Press and hold
IMPRINT
(iDA-X303 only) or
SOUND
(iDA-X301/iDA-X301RR only) for at least 2
seconds to activate the AUDIO selection mode.
2
Turn the
Double Action encoder
(iDA-X303 only)
or
Rotary encoder
(iDA-X301/iDA-X301RR only) to
select the SUBW SYSTEM mode, and then press
/
ENTER
.
SUBW
SUBW SYSTEM
*
BASS
TREBLE
HPF
SUBW
* Displayed only when subwoofer is ON.
3
Turn the
Double Action encoder
(iDA-X303 only)
or
Rotary encoder
(iDA-X301/iDA-X301RR only) to
select the SUBW SYS 1 or SUBW SYS 2, and then
press
/
ENTER
.
SYS 1
SYS 2
Sound Setting
Double Action encoder
IMPRINT
/ENTER
PRESET
Rotary encoder
SOUND
/ENTER PRESET
SYS 1:
Subwoofer level changes according to the main volume
setting.
SYS 2:
Subwoofer level change is different from the main
volume setting. For example, even at low volume
settings, the subwoofer is still audible.
