33
-EN
4
Repeat steps 1 to 3 to set another speaker.
By setting these values to make its sound reach the
listening position at the same time as the sound of other
speakers.
•
You can select the next band by pressing and turning the
Double
Action encoder
.
•
The User Preset screen can be recalled in the normal mode by
pressing and holding PRESET for 2 seconds.
Adjusting the Crossover Settings (X-OVER)
Before performing the following procedures, refer to “About the
Crossover” (page 36).
2.2ch (3WAY) System
1
After selecting X-OVER from the Sound Field
Adjustment mode, turn the
Double Action
encoder
to select the band adjustment, and then
press
/
ENTER
.
2.2ch (3WAY) System / NORMAL (L=R)
Setting items:
LOW / MID-L / MID-H / HIGH
2.2ch (3WAY) System / INDIVIDUAL (L/R)
Setting items:
LOW-L / LOW-R / MID-L-L / MID-L-R / MID-H-L /
MID-H-R / HIGH-L / HIGH-R
2
Turn the
Double Action encoder
to select an item
to adjust, then press
/
ENTER
.
Cut-off frequency
3
-1 Turn the
Double Action encoder
to select the
desired cut-off frequency (Crossover Point).
Adjustable frequency bands:
2.2ch (3WAY) System
Setting items:
LOW / MID-L 20 Hz~200 Hz
MID-H
20 Hz~20 kHz
HIGH
(1 kHz~20 kHz)
*
1
/(20 Hz~20 kHz)
*
2
*
1
When Maker’s is selected, refer to “Setting the Response Slope for
the High Range Speaker (TW Setup)” (page 34).
*
2
When User’s is selected, refer to“Setting the Response Slope for the
High Range Speaker (TW Setup)” (page 34).
Level Adjustment
3
-2 Turn the
Double Action encoder
to adjust the
output level.
Adjustable output level: –12 to 0 dB.
Slope Adjustment
3
-3 Turn the
Double Action encoder
to adjust the
slope.
Adjustable slope: FLAT
*
, 6 dB/oct., 12 dB/oct., 18 dB/oct.,
24 dB/oct.
* FLAT can be set for the HIGH slope only when User’s is selected in
“Setting the Response Slope for the High Range Speaker
(TW Setup)” (page 34). Depending on the response characteristics of
the speaker, care should be taken when setting the response slope to
FLAT, as speaker damage may result. With this unit, a message is
displayed when the response slope for the high range speaker is set
to FLAT.
4
Repeat steps 1 to 3 to make adjustment to the other
bands.
4.2ch (FRONT/REAR/SUBW.) System
1
After selecting X-OVER from the Sound Field
Adjustment mode, turn the
Double Action
encoder
to select the band adjustment, and then
press
/ENTER
.
4.2ch (FRONT/REAR/SUBW.) System / NORMAL (L=R)
setting items:
LOW (SUB-W) / MID (REAR) / HIGH (FRONT)
4.2ch (FRONT/REAR/SUBW.) System / INDIVIDUAL (L/R)
setting items:
LOW (SUB-W)-L / LOW (SUB-W)-R / MID (REAR)-L /
MID (REAR)-R / HIGH (FRONT)-L / HIGH (FRONT)-R
2
Turn the
Double Action encoder
to select an item
to adjust, then press
/ENTER
.
Cut-off frequency
3
-1 Turn the
Double Action encoder
to select the
desired cut-off frequency (Crossover Point).
Adjustable frequency bands:
4.2ch (FRONT/REAR/SUBW.) System
Setting items:
20 Hz~200 Hz
Level Adjustment
3
-2 Turn the
Double Action encoder
to adjust the
output level.
Adjustable output level: -12 to 0 dB.
Slope Adjustment
3
-3 Turn the
Double Action encoder
to adjust the
slope.
Adjustable slope: FLAT, 6 dB/oct., 12 dB/oct., 18 dB/oct.,
24 dB/oct.
4
Repeat steps 1 to 3 to make adjustment to the other
bands.
•
You can select the next band by pressing and turning the
Double
Action encoder
.
•
While adjusting the X-over, you should consider the frequency
response of the connected speakers.
•
About the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) system
You can switch to 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.)
system mode with the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.)
switch on the PXA-H100. For details, refer to the Owner’s Manual of
PXA-H100.
•
The User Preset screen can be recalled in the normal mode by
pressing and holding PRESET for 2 seconds.
FC
LV
SLP
FC
(cut-off (level) (slope) (frequency)
frequency)
FC
LV
SLP
FC
(cut-off (level) (slope) (frequency)
frequency)
