background image

8

For more information about our company or products, please visit our website at www.alpine4u.com or call us (USA) 1-877-710-0162

OPERATION AND MAINTENANCE

WARNING

:

 

Always unplug or disconnect all appliances in the pond from the electrical supply before installing, 

repairing, maintaining or handling the equipment in the water.

-Once a week, verify that the pump performance is satisfactory.  If you detect a drop in pump performance (such as 

a decrease in water flow from the pump or to the waterfall) first clean the pump’s pre-filter cage and tubing.  If the 

water flow is still not fully restored to its original performance, clean the rotor impeller and motor casing.

-The pump impeller includes a high quality ceramic shaft that provides long-lasting, reliable performance when 

properly maintained.  However, extreme care should be taken when handling the shaft during maintenance. Avoid 

dropping or pressing too hard on it to avoid breakage or hairline fractures, which may cause the shaft to snap while 

in operation.

-This pump is suitable for use in water temperatures from 32 degrees Fahrenheit (0 degrees Celsius) to 95 degrees

Fahrenheit (35 degrees Celsius).

-To keep the pump in long lasting working conditions, always replace any worn parts.

Do not remove the pump’s pre-filter cage while operating the pump.  Failure to operate the pump without the

pre-filter cage or operating the pump with a broken cage will allow large debris to enter the pump causing damage 

to the pump, thus voiding the warranty.

We recommend inspecting your pump on a regular basis to ensure it is functioning properly.  If you notice the water 

flow rate diminish, it may be due to the pump’s pre-filter cage being blocked with debris.  In many cases, the clogged 

filter cage can be cleaned by reaching into the pond and pulling the pump out of the water to remove the debris 

from the filter cage

Important Note: 

Always disconnect the power before performing maintenance on the pump. Pull off any debris 

stuck to the pump pre-filter cage and/or use a garden hose to spray off any debris stuck to the filter cage.

To avoid shortening the life of the pump, follow these simple maintenance procedures:

Pump Pre-Filter Cage

Pump Pre-Filter Cleaning

Summary of Contents for eco-SPHERE PUR1400












Reviews: