16
-EN
Adjusting Subwoofer Level/Balance
(Between Left and Right)/Fader (Between
Front and Rear)/Auto Volume/Black Out/
Defeat
1
Press
AUDIO
repeatedly to choose the desired mode.
Each press changes the mode as follows:
SUBWOOFER
*1
BALANCE
FADER
AUTO VOLUME
*2
BLACK OUT
*3
DEFEAT
VOLUME
SUBWOOFER
*1
When the subwoofer mode is set to OFF, its level cannot be
adjusted, refer to “Turning Subwoofer ON/OFF” on page 16.
*2
By setting AUTO VOLUME, the unit can automatically adjust
volume to a proper level according to engine/road noise, etc.
There are three volume correction degrees: LOW, MIDDLE and
HIGH.
*3
When Blackout mode is turned on, after 5 seconds, all display
indications on this unit will turn off to reduce power
consumption. This additional power enhances the sound quality.
Notes
• If no operation is performed for 5 seconds after selecting the
SUBWOOFER, BALANCE, FADER, AUTO VOLUME, BLACK OUT
or DEFEAT mode, the unit automatically returns to normal mode.
• If any button on the unit is pressed during the Blackout Mode, the
function is displayed for 5 seconds before returning to Blackout mode.
2
Turn the
Rotary encoder
until the desired sound is
obtained in each mode.
Note
• Depending on the connected devices, some functions and display
indications do not work.
Sound Setting
You can flexibly customize the unit to suit your own preference and
usage. From the SOUND SETUP menu, Audio Setting can be modified.
1
Press and hold
SOUND SETUP
for at least 2 seconds to
activate the Sound Setting mode.
2
Turn the
Rotary encoder
to select the desired sound
setting menu, and then press
ENTER
.
HPF
*1
Subwoofer
SUBW. System
*2
SUBW. Phase
*2
SUBW. Channel
*2
Media Xpander
MX Level
*3
EQ Mode
TCR Parameter
Sound Field
*4
HPF
*1
Adjustment cannot be performed when an external audio
processor is connected or Defeat is set to ON.
*2
These functions are inoperable when Subwoofer is set to OFF.
*3
This function is effective only when Media Xpander is set to ON.
*4
In step 2, two sound adjustment items (Parametric EQ/Graphic
EQ, T.Correction) can be selected in Sound Field Adjustment
mode, turn the
Rotary encoder
to select the desired item, and
then press
ENTER
to continue to step 3.
3
Turn the
Rotary encoder
to change the setting, and then
press
ENTER
.
(e.g. Select Subwoofer ON or Subwoofer OFF)
4
Press and hold
ESC
for at least 2 seconds to return to
normal mode.
Notes
• Media Xpander, Parametric EQ/Graphic EQ Adjustment, EQ Mode
and MX Level Adjustment are inoperable when Defeat is set to ON.
• Pressing
ESC
returns to the previous Sound menu mode.
• If no operation is performed for 60 seconds, Sound menu mode is
cancelled.
The High Pass Filter on this unit can be adjusted to suit your personal
taste.
Setting item:
HPF
Setting contents:
OFF (Initial setting) / 60 Hz / 80 Hz / 100 Hz
When the subwoofer is on, you can adjust the subwoofer output level
(refer to “Sound Setting” on page 16).
Setting item:
Subwoofer
Setting contents:
ON (Initial setting) / OFF
ON:
The subwoofer signal is output from the Subwoofer RCA
Connectors (refer to “Connections” on page 47).
OFF:
No subwoofer signal is output from the Subwoofer RCA
Connectors (refer to “Connections” on page 47).
Sound Setting
Subwoofer level
0 ~ 15
Balance
–15(L) ~ 15(R)
Fader
–15(R) ~ 15(F)
Auto Volume
OFF/LOW/MIDDLE/HIGH
Black Out
ON/OFF
Defeat
ON/OFF
Volume
0 ~ 35
/ESC
BAND/TA
AUDIO/SOUND SETUP
SOURCE/
Rotary encoder/ENTER/
Preset buttons (1 through 6)
Use steps 1 to 4 to select one of the setting modes to modify.
See the applicable section below for details about the
selected setting item.
Adjusting the High Pass Filter
Turning Subwoofer ON/OFF
Summary of Contents for CDA-117Ri
Page 2: ......
