background image

Serial #: 

Date Installed: 

Your Dealer: 

 

c.p. Allstar Corporation 
Downingtown, PA  19335 

This garage door opener is built in the USA 
and complies with all requirements of 
Underwriters Laboratories Standard UL-325.   
P/N 112075 

Rev. B 

     March  2006

 

 

Manufacturer’s Limited Warranty

 

Allstar warrants its 9000M Series Challenger residential vehicular garage door openers as follows: 

A. 

   The drive train to be free from defects in materials and workmanship for: 

 

Models 9300M/9500M/J9500M:  for 10 years from the date of purchase by the 

  original 

purchaser. 

 

The drive train includes the motor, rails, frame and chain. 

B.

  The controller circuit board, capacitor, photobeams and all other parts in all models will be free 

from defects in materials and workmanship for a period of two (2) years from the date of purchase 
by the original purchaser. 

Contact your dealer to obtain service for your opener . 

To obtain service under this warranty the buyer must obtain authorization instructions for the return of 
any goods from Allstar before returning the goods.  The goods must be returned with complete 
identification, with copy of proof-of-purchase, freight prepaid and in accordance with Allstar's 
instructions or they will not be accepted.  In no event will Allstar be responsible for goods returned 
without proper authorization or identification. 

Goods returned to Allstar for warranty repair within the warranty period, which upon receipt by Allstar 
are confirmed to be defective and covered by this limited warranty, will be repaired or replaced at 
Allstar's sole option, at no cost and returned pre-paid.  Defective parts will be repaired or replaced with 
new or factory rebuilt parts at Allstar’s sole option. 

This limited warranty does not cover non-defect damage, damage caused by unreasonable use, damage 
caused by improper installation or care, vandalism or lightning, fire or excessive heat, flood or other acts 
of God (including, but not limited to misuse, abuse or alterations, failure to provide reasonable and 
necessary maintenance), labor charges for dismantling or reinstalling a repaired or replaced unit, or 
replacement batteries. 

These warranties are in lieu of all other warranties, either expressed or implied.  All implied warranties 
of merchantability and/or fitness for a particular purpose are hereby disclaimed and excluded.  Under no 
circumstances shall Allstar be liable for consequential, incidental or special damages arising in 
connection with the use or inability to use this product.  In no event shall Allstar’s liability for breach of 
warranty, breach of contract, negligence or strict liability exceed the cost of the product covered hereby.  
No person is authorized to assume for Allstar any other liability in connection with the sale of this 
product. 

This warranty gives you specific legal rights.  You may also have other rights which vary from state to 
state.  Warranty effective after May 1, 2004.

 

See Page 14 for Radio System 
programming instructions and 
FCC/RSS-210 Industry Canada 
statement.  Allstar opener radio 
systems are HomeLink® 
compatible. 

Code Position 

Ö

  1 

 Plus 

(+) 

Button 

 

 

 

 

 

 

 

 

 

Zero 

(0) 

Button  

 

 

 

 

 

 

 

 

 

Minus 

(-)

 Button  

 

 

 

 

 

 

 

 

 

Your Radio System can learn 

8 different

 transmitter codes.  See Page 14 and, if desired, record your code settings below. 

 

Summary of Contents for Challenger 9000M Series





















Reviews: