4
PROGRAMMING YOUR PIN
It is now time to change the factory default PIN of 1, 2, 3, 4 to your own
private PIN.
STEP 1:
Begin by filling out the table above.
You may program up to four PIN Codes. The PIN No. entry represents
the first, second, third and fourth PIN you are choosing to program. In
the table above, PIN No. 1 represents the required entry for program-
ming the first PIN you have selected. This first PIN will be your
Primary PIN.
A sample block has been filled out below. In this example the
PRIMARY PIN is the factory preset code. The PIN No. 3 indicates the
third code in your system (this may be valid even if you do not have a
second code). New PIN Code 5127 is an example representing the new
PIN Code you have chosen.
NOTE: DO NOT REVEAL YOUR PRIMARY PIN CODE.
IT IS THE ONLY NUMBER WHICH CAN BE USED FOR
PROGRAMMING AND IS YOUR INSURANCE AGAINST
ANYONE REPROGRAMMING YOUR KEYPAD.
PROGRAMMING INSTRUCTIONS
Manufacturer’s Limited Warranty
Allstar warrants its radio controls to be free from defect in material and workmanship for a period of one (1) year from the date of purchase. To obtain service,
contact your dealer.
To obtain service under this warranty the buyer must obtain authorization instructions for the return of any goods from Allstar before returning the goods. The
goods must be returned with complete identification, with copy of proof-of-purchase, freight prepaid and in accordance with Allstar’s instructions or they will not
be accepted. In no event will Allstar be responsible for goods returned without proper authorization or identification.
Goods returned to Allstar for warranty repair within the warranty period, which upon receipt by Allstar are confirmed to be defective and covered by this limited
warranty, will be repaired or replaced at Allstar’s sole option, at no cost and returned pre-paid. Defective parts will be repaired or replaced with new or factory
rebuilt parts at Allstar’s sole option.
This limited warranty does not cover non-defect damage, damage caused by unreasonable use, damage caused by improper installation or care, vandalism or
lightning, fire or excessive heat, flood or other acts of God (including, but not limited to misuse, abuse or alterations, failure to provide reasonable and necessary
maintenance), labor charges for dismantling or reinstalling a repaired or replaced unit, or replacement batteries.
These warranties are in lieu of all other warranties, either expressed or implied. All implied warranties of merchantability and/or fitness for a particular purpose are
hereby disclaimed and excluded. Under no circumstances shall Allstar be liable for consequential, incidental or special damages arising in connection with the use
or inability to use this product. In no event shall Allstar’s liability for breach of warranty, breach of contract, negligence or strict liability exceed the cost of the
product covered hereby. No person is authorized to assume for Allstar any other liability in connection with the sale of this product.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Warranty effective after May 15th, 1997.
For Information:
To operate your new wireless keypad press the RESET/ON key to light
or reset your keypad. Enter your PIN followed by the * symbol and
then your door umber. For example:
Your operator should be activated. If not, try again, making certain you
are entering the correct PIN.
If your operator is still not activated, a programming error may have
been made. Repeat the programming steps outlined in the Programming
Instructions section of this manual.
OPERATING INSTRUCTIONS
c.p. Allstar Corporation
P.O. Box 240
Downingtown, PA 19335
P/N 104096, Rev E, 2/99
1
2
3
4
#
1
#
Factory Default Pin
Pin No.
New Pin
Repeat New Pin
STEP 2:
Press the ON/RESET button and enter all of the characters
in the sequence shown in the table at the top of the page.
STEP 3:
Check your new setting by entering your new PIN Code,
followed by * and the number of the door you wish to activate. The
operator should respond. If not, repeat steps 5 and 6. Press the
RESET/ON button should you press an incorrect key, and begin pro-
gramming again.
1
2
3
4
#
3
5
1
2
7
5
1
2
7
#
Factory Default Pin
Pin No.
New Pin
Repeat New Pin
5
1
2
7
*
Activate Keypad
Your PIN
Door Number
ON/RESET
1
