manualshive.com logo in svg

Allied Telesis CentreCOM GS970M Series, Quick Installation Manual, Page: 18 / 21

Share
Download
Allied Telesis CentreCOM GS970M Series Quick Installation Manual Download Page 18

18

CentreCOM GS970M Series Quick Installation Guide

System LEDs

The System LEDs are described here.

Solid green

The port has established a 1Gbps link to a 

network device.

Flashing green

The port is transmitting or receiving packets at 

1Gbps.

Off

Possible causes of this state are listed here:

- The SFP transceiver port is empty.

- The SFP transceiver has not established a 

link with another network device.

- The LEDs are turned off. To turn on the 

LEDs, use the eco-friendly button.

SD LED

Solid green

The switch has detected an SD card in the SD 

slot.

Flashing green

The switch is writing to or reading from the SD 

card.

Flashing amber

The switch encountered an error with the SD 

card.

Off

The SD slot is empty or the LEDs are off.

Fault

Flashing red 

once

The switch’s fan is failing or has stopped.

Flashing red six 

times

The switch is overheating and might shut 

down.

Off

The switch is operating normally.

Summary of Contents for CentreCOM GS970M Series






















Reviews:

No comments