manualshive.com logo in svg

Allied Telesis CentreCOM AT-200 Series, User Manual, Page: 12 / 19

Share
Download
Allied Telesis CentreCOM AT-200 Series User Manual Download Page 12

 

AT-200 Single Port Transceiver

5

 

11. To install the transceiver, align the opening on the transceiver body so that 

the diagnostic LEDs are facing you. (The transceiver is reversible front to 
back.) Gently guide the tap body into the transceiver opening so that the 
probe post and the two braid terminator posts are aligned with the three 
gold-colored circuit board contacts. Then slide the tap assembly fully into 
the slot.

12. Secure the tap body to transceiver with the two panhead screws.

 

Replacement probe assembly and braid terminators are available as 

 

tool kit AT-060-K.

13. Be sure the cable is terminated at both ends. Figure 3 shows a terminator 

installed at one end of a thicknet segment.

 

Figure 3: 

 

50 

 

Ω 

 

Terminator for Thicknet Segment

 

Thick Ethernet installation with coaxial N-series tap (for model 
AT-208)

 

Before installing the AT-208 Single Port Transceiver, check to see that the 
transceiver package contents are complete. If any of the following items are 
missing or damaged, contact your sales representative.

 

❑

 

AT-200 Series Single Port Transceiver with AT-08 tap

 

❑

 

Manual

 

❑

 

Warranty card

No assembly of the transceiver is required. It comes with the tap body factory 
installed. See Figure 4.

Note

 Thicknet
 terminator

Cable

 

613-10423-00Book  Page 5  Monday, March 4, 1996  2:29 PM

Summary of Contents for CentreCOM AT-200 Series




















Reviews:

No comments