manualshive.com logo in svg

Allied Telesis CentreCOM AT-200 Series, User Manual, Page: 19 / 19

Share
Download
Allied Telesis CentreCOM AT-200 Series User Manual Download Page 19

 

CentreCOM is a trademark of Allied Telesyn International Corp.

Copyright 1994 Allied Telesyn International Corp.
All rights reserved. No part of this publication may be reproduced without prior 
written permission from Allied Telesyn International Corp. 

Allied Telesyn International Corp. reserves the right to make changes in 
specifications and other information contained in this document without prior 
written notice. The information provided herein is subject to change without 
notice. In no event shall Allied Telesyn International Corp. be liable for any 
incidental, special, indirect, or consequential damages whatsoever, including but 
not limited to lost profits, arising out of or related to this manual or the information 
contained herein, even if Allied Telesyn International Corp. has been advised of, 
known, or should have known, the possibility of such damages.

Allied Telesyn

950 Kifer Road

Sunnyvale, CA  94086  USA

Tel (800) 424-4284 • Fax (408) 736-0100

Technical Support Tel (800) 428-4835 • Fax (206) 481-3790

 

613-10423-00Book  Page 12  Monday, March 4, 1996  2:29 PM

Summary of Contents for CentreCOM AT-200 Series




















Reviews:

No comments