Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 51

Page: 51 / 356

SwitchBlade x8106 Chassis Switch and AT-SBx81CFC960 Card Installation Guide

Section I: Hardware Overview

AT-SBx81XS16 SFP+ Line Card

The AT-SBx81XS16 Line Card, shown in Figure 23, is an Ethernet switch
that supports 10Gbps SFP+ transceivers.

Figure 23. AT-SBx81XS16 Line Card

Here are the main features of the line card:



Sixteen slots for 10Gbps SFP+ transceivers



Supports 10GBase-SR/LR fiber optic transceivers



Supports AT-SP10TW connect twinax cables with SFP+
transceiver-style connectors



Port Link/Activity (L/A) LEDs



32K entry MAC address table



32 Mb buffer memory



Jumbo frame support of up to 10240 bytes



Hot swappable

Contact your Allied Telesis sales representative for a list of supported
transceivers.

Note

This line card is not supported by the AT-SBx81CFC400 Controller
Fabric Card.

LEDs

The AT-SBx81XS16 Line Card has one LED for each SFP+ slot. The LED
is shown in Figure 24 on page 52 and described in Table 12 on page 52.

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands