Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 49

Page: 49 / 356

SwitchBlade x8106 Chassis Switch and AT-SBx81CFC960 Card Installation Guide

Section I: Hardware Overview

AT-SBx81XS6 SFP+ Line Card

The AT-SBx81XS6 Line Card, shown in Figure 21, is a 10Gbps Ethernet
switch.

Figure 21. AT-SBx81XS6 Line Card

Here are the main features of the line card:



Six slots for 10Gbps SFP+ transceivers



Supports 10GBase-SR/LR fiber optic transceivers



Supports AT-SP10TW direct connect twinax cables with SFP+
transceiver-style connectors



Port Link/Activity (L/A) LEDs



32K entry MAC address table



24 Mb buffer memory



Jumbo frame support:

–

9710 bytes for ports operating at 10 or 100 Mbps.

–

10240 bytes for ports operating at 1000 Mbps



Hot swappable

Contact your Allied Telesis sales representative for a list of supported
transceivers.

LEDs

The AT-SBx81XS6 Line Card has one LED for each SFP+ slot. The LED
is shown in Figure 22 and described in Table 11 on page 50.

Figure 22. SFP+ Slot LEDs on the AT-SBx81XS6 Line Card

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands

Allied Telesis AT-SB*81CFC960, Installation Manual

Search results

Summary of Contents for AT-SB*81CFC960

Reviews:

Related manuals for AT-SB*81CFC960

Brands by name

Popular brands