Allied Telesis AT-SB*81CFC960 Installation Manual Download Page 262 | Manualshive

Page: 262 / 356

background image

Chapter 13: Replacing Modules

262

Section II: Installing the Chassis

Replacing the AT-SBxPWRSYS1 DC Power Supply

This section contains the procedure for removing the AT-SBxPWRSYS1
DC Power Supply from the AT-SBx8106 Chassis.

Note

Allied Telesis recommends creating a backup copy of the
configuration file in the controller card before removing or replacing
a power supply. For instructions, refer to the

Software Reference for

SwitchBlade x8100 Series Switches

on the Allied Telesis web site.

Note

The power supply is hot swappable.

To remove the AT-SBxPWRSYS1 DC Power Supply from the chassis,
perform the following procedure:

1. Turn off the circuit breaker to the AT-SBxPWRSYS1 DC Power

Supply.

2. Turn off the On/Off switch on the front panel of the power supply. Refer

to Figure 122 on page 202.

3. Use a #2 screwdriver to loosen the screw on the locking handle. Refer

to Figure 161 on page 263.

Note

Do not lift the locking handle yet.

«
...
260
261
262
263
264
...
»

Summary of Contents for AT-SB*81CFC960





































































































































































































































































































































































Reviews:

No comments

Related manuals for AT-SB*81CFC960

Brand: GE Pages: 6

Brand: N-Tron Pages: 62

InterReach Fusion ADCP-77-044

Brand: TE Connectivity Pages: 236

RouterBOARD SXT 5HnD

Brand: MikroTik Pages: 2

Brand: 3Com Pages: 50

Brand: Patton electronics Pages: 9

Brand: Qlogic Pages: 8

Brand: Gira Pages: 6

AceroDURO 100/S100

Brand: CNC-Step Pages: 86

Brand: Hi-flying Pages: 59

Brand: Pro-Nets Technology Corporation Pages: 48

Wisenet XRN-6410DB4

Brand: Hanwha Techwin Pages: 118

Brand: IC Realtime Pages: 8

Brand: Cambium Networks Pages: 560

Brand: Johnson Controls Pages: 5

Brand: A-Link Pages: 28

Brand: CYP Pages: 16

nastorage 12600 series

Brand: Ingrasys Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands