background image

AT-S87 Version 1.0.0 Software Release Notes

PN 613-000911 Rev B

1

Allied Telesis, Inc.

AT-S87 Version 1.0.0

AT-GS950/48 Gigabit Ethernet Smart Switch

Software Release Notes

Please read this document before you begin to use the management software.

Supported Platforms

AT-S87 Version 1.0.0 Management Software is supported on the AT-GS950/48 Gigabit Ethernet 
Smart Switch only.
The AT-GS950/48 Gigabit Ethernet Smart Switch supports the following ATI 100 MB SFP 
modules:

ˆ

AT-SPFX/2

ˆ

ATSPFX/15

ˆ

AT-SPFX/40

The AT-GS950/48 Gigabit Ethernet Smart Switch supports the following ATI 1000 MB SFP 
modules:

ˆ

AT-SPSX

ˆ

AT-SPLX10

ˆ

AT-SPLX40

ˆ

AT-SPZX80

Product Documentation

Refer to the Allied Telesis web site at 

www.alliedtelesis.com

 for the latest installation and user 

guides.

New Features

Version 1.0.0:

ˆ

LEDs for unit and port status

ˆ

48 Auto-Negotiating 10/100/1000Base-T twisted pair ports with RJ-45 connectors

ˆ

Four small form-factor pluggable (SFP) ports

ˆ

Auto MDI/MDI-X on the twisted pair ports

ˆ

IEEE 802.3 and IEEE 802.3u compliant

ˆ

IEEE 802.3x flow control in full-duplex operation; back pressure in half-duplex operation

ˆ

Store and forward switching mode

ˆ

MAC address table capacity of up to 8K addresses with automatic aging

ˆ

Web-based configuration using the AT-S87 management software

ˆ

SNMPv1 and SNMPv2c  management

ˆ

Port Trunking

ˆ

Port Mirroring

ˆ

VLANs

Summary of Contents for AT-S87

Page 1: ... ATI 1000 MB SFP modules AT SPSX AT SPLX10 AT SPLX40 AT SPZX80 Product Documentation Refer to the Allied Telesis web site at www alliedtelesis com for the latest installation and user guides New Features Version 1 0 0 LEDs for unit and port status 48 Auto Negotiating 10 100 1000Base T twisted pair ports with RJ 45 connectors Four small form factor pluggable SFP ports Auto MDI MDI X on the twisted ...

Page 2: ...into the AT GS950 48 Gigabit Ethernet Smart Switch it will not be auto detected and thus will initially not be operational In order to make the SFP module active you must manually configure each individual SFP port as follows where the 100FX SFP is used 1 From the main menu on the left hand side of the web management page select Physical Interface and the Physical Interface page is displayed 2 In ...

Page 3: ...ation by setting the SFP port Mode to 1G Full per the procedure given above To activate a port configuration change be sure to perform the following steps after selecting and changing a configuration parameter for either a copper or SFP port on the Physical Interface page 1 Click the Modify button on the Physical Interface page 2 Click the OK button on the Physical Interface page 3 To activate the...

Page 4: ...s and conditions of the warranty and for warranty registration Obtaining Management Software Updates New releases of management software for our managed products are available from the following Internet sites Allied Telesis web site www alliedtelesis com Allied Telesis FTP server ftp ftp alliedtelesis com If the FTP server prompts you to log on enter anonymous as the user name and your email addr...

Reviews: