manualshive.com logo in svg

Allied Telesis AT-MR420T, Installation Manual

Share
Download
Allied Telesis AT-MR420T Installation Manual Download Page 57

AT-MR420T and AT-MR820T Installation Guide

35

SQE TEST—Commonly referred to as Heartbeat, is a special 802.3 signal sent 
by the MAU to the DTE to test the collision detection function. Some DTE want 
SQE and others do not. Repeaters do not want the SQE Test.

STRAIGHT-THROUGH—A type of wiring connection where the pins of one 
connector connect to the same pins of another connector. For example, pin 1 of 
one connector connects to pin 1 of another connector.

THICK ETHERNET—See 10Base5

THIN ETHERNET—See 10Base2

TRUNK CABLE—The coaxial cable used to distribute signals over long 
distances throughout a cable system.

UNSHIELDED TWISTED PAIR (UTP)—A cable used in 10Base-T wiring 
that consists of at least two twisted pairs of 22 to 26 AWG wire. The pairs 
should have at least 3 twists per foot and have an impedance of 100 

Ω

. Level 3, 

Level 4 and Level 5 UTP cables fit these criteria. 

MRx20T(UTP)Ver6_Book  Page 35  Thursday, April 3, 1997  5:18 PM

Summary of Contents for AT-MR420T



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands