Allied Telesis AT-MC105XL Installation Manual Download Page 13

AT-MC105XL and AT-MC106XL Installation Guide

7

Back-to-Back Installation

Review the following before doing a back-to-back installation. See Figure8 f or 
an illustration of a back-to-back-media converter configuration.

During installation, setup, and testing of back-to-back media 
converters, make sure each media converter is in the Link Test Mode.

When two media converters are connected back-to-back with no UTP/
STP cables connected and when the NML/LNK TST switch is in the 
OUT position (Link Test Mode), the fiber REC LEDs on each converter 
may flash. This is normal and will not affect the normal operation of 
the converters.

When operating two media converters in a back-to-back configuration, 
Allied Telesyn recommends that the MissingLink feature on one or 
both of the converters be disabled. The MissingLink feature can be 
disabled by placing the NML/LNK TST switch in the OUT position 
(LNK TST Mode). Disabling the Link Test Mode does not interfere 
with the converter’s ability to pass network traffic. 

Rack-mount Chassis Installation

To install the media converter in the rack-mount chassis, refer to the 
“AT-MCR12 Media Converter Chassis Installation Manual” or visit the 
Technical Support area of Allied Telesyn’s website at 
www.alliedtelesyn.com. Figure 6 shows the AT-MCR12 rack-mount chassis

Figure 6  AT-MCR12 Rack-mount Chassis

1

0

0Base

-FX

REC

PWR

LNK

1

0

0Base

-TX

REC

LNK

MDI

MDI-X

TX

RX

MC

1

02  FAST ETHERNET MEDIA CONVERTER

1

0

0Base

-FX

REC

PWR

LNK

1

0

0Base

-TX

REC

LNK

MDI

MDI-X

TX

RX

MC

1

02  FAST ETHERNET MEDIA CONVERTER

1

0

0Base

-FX

REC

PWR

LNK

1

0

0Base

-TX

REC

LNK

MDI

MDI-X

TX

RX

MC

1

02  FAST ETHERNET MEDIA CONVERTER

1

0

0Base

-FX

REC

PWR

LNK

1

0

0Base

-TX

REC

LNK

MDI

MDI-X

TX

RX

MC

1

02  FAST ETHERNET MEDIA CONVERTER

1

0

0Base

-FX

REC

PWR

LNK

1

0

0Base

-TX

REC

LNK

MDI

MDI-X

TX

RX

MC

1

02  FAST ETHERNET MEDIA CONVERTER

1

0

0Base

-FX

REC

PWR

LNK

1

0

0Base

-TX

REC

LNK

MDI

MDI-X

TX

RX

MC

1

02  FAST ETHERNET MEDIA CONVERTER

1

0

0Base

-FX

REC

PWR

LNK

1

0

0Base

-TX

REC

LNK

MDI

M

DI-X

TX

RX

MC

1

02  FAST ETHERNET MEDIA CONVERTER

1

0

0Base

-FX

REC

PWR

LNK

1

0

0Base

-TX

REC

LNK

MDI

MDI-X

TX

RX

MC

1

02  FAST ETHERNET MEDIA CONVERTER

1

0

0Base

-FX

REC

PWR

LNK

1

0

0Base

-TX

REC

LNK

MDI

MDI-X

TX

RX

MC

1

02  FAST ETHERNET MEDIA CONVERTER

1

0

0Base

-FX

REC

PWR

LNK

1

0

0Base

-TX

REC

LNK

MDI

MDI-X

TX

RX

MC

1

02  FAST ETHERNET MEDIA CONVERTER

1

0

0Base

-FX

REC

PWR

LNK

1

0

0Base

-TX

REC

LNK

MDI

MDI-X

TX

RX

MC

1

02  FAST ETHERNET MEDIA CONVERTER

1

0

0Base

-FX

REC

PWR

LNK

1

0

0Base

-TX

REC

LNK

MDI

MDI-X

TX

RX

MC

1

02  FAST ETHERNET MEDIA CONVERTER

MCR12

Summary of Contents for AT-MC105XL





























Reviews: