Allied Telesis AT-6102 Installation And User Manual Download Page 2

 

AT-6102 Installation and User Guide 

Electrical Safety and Emissions Standards 

Standards

: This product meets the following standards. 

U.S. Federal Communications Commission 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 

This device may not cause harmful interference. 

This device must accept any interference received, including interference that may cause undesired operation. 

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, 

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the 

following measures: 

- Reorient or relocate the receiving antenna. 

- Increase the separation between the equipment and receiver. 

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

- Consult the dealer or an experienced radio/TV technician for help. 

 

Canadian Department of Communications 

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. 

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. 

 

Safety and Electromagnetic Emissions Certifications 

 
EMI/RFI and Immunity:  FCC Part 15 Class B; FCC Part 15B, 15C, and 15E Certified; EN 

55022/CISPR 22 Class B; ; EN 301 893; EN 300 328; EN 301 489 
Transmitter EMC; Canada IC; CE Mark emission/immunity; CE Marked 
(compliant with RTT&E, EMC, LVD Directives); C-Tick; GOST 

Electrical Safety: 

UL 60950-1, CSA C22.2 No. 60950-1-03 (

C

UL

US

), EN60950-1, EN 

60593-IP53; GOST 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Copyright © 2006 Allied Telesis, Inc. 

All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. 

Microsoft and Internet Explorer are registered trademarks of Microsoft Corporation. Netscape Navigator is a registered trademark of Netscape 

Communications Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or 

registered trademarks of their respective owners. 

Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior written 

notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be liable for any incidental, 

special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this manual or the 

information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility of such damages.. 

Summary of Contents for AT-6102









Reviews: