background image

22

SHOW IGMPSNOOPING ROUTERADDRESS

Patch Release Note

Patch 86253-07 for Software Release 2.5.3

C613-10382-00 REV E

Incorrect debug information was returned when an ICMPv6 

PacketTooBig

 

message was received. This issue has been resolved.

ISAKMP in 

aggressive

 mode did not establish a connection when the peer 

client sent 10 or more payloads. This issue has been resolved.

The IPSec configuration was not created correctly when the RADDRESS 
and LNAME parameters in the CREATE IPSEC POLICY command were 
used together. This issue has been resolved.

The CREATE IPSEC POLICY command failed if the interface specified with 
the INTERFACE parameter did not have a global IPv6 interface defined. 
This PCR implements a workaround by using the interface’s link-local IPv6 
address if no other IPv6 address can be found.

ISAKMP debug messages now correctly output IPv6 addresses when using 
IPv6, and IPv4 addresses when using IPv4.

When ISAKMP was used with IPv6, an incorrect IP address was displayed 
in the output of the SHOW ISAKMP EXCHANGE command. This issue has 
been resolved.

DHEXPONENTLENGTH parameter in the CREATE ISAKMP POLICY 
command was not accepted when creating ISAKMP policies that used IPv6. 
This issue has been resolved.

When a 

NeighbourAdvert

 message containing an anycast target address was 

received, the device incorrectly performed Duplicate Address Detection. 
This issue has been resolved.

When IPSec was used with IPv6, an incorrect IP address was displayed in 
the output of the SHOW IPSEC SA command. This issue has been resolved.

If a local IP address and remote IP address were not specified in the 
CREATE IPSEC POLICY command for IPv6 IPSec, the SET IPSEC POLICY 
configuration was shown unnecessarily in the output of the SHOW 
CONFIG DYNAMIC=IPSEC command. This issue has been resolved.

MAC address are now deleted from the all the internal tables for ports 
where the learn limit has been exceeded.

PCR: 03925

Module: IPV6

                                  Level: 3

PCR: 03928

Module: IKMP

                                  Level: 2

PCR: 03931

Module: IPSEC

                                  Level: 3

PCR: 03934

Module: IPSEC

                                  Level: 2

PCR: 03935

Module: ISAKMP

                                  Level: 3

PCR: 03936

Module: IKMP

                                  Level: 3

PCR: 03938

Module: IKMP

                                  Level: 3

PCR: 03939

Module: IPV6

                                  Level: 2

PCR: 03946

Module: IPSEC

                                  Level: 3

PCR: 03949

Module: IPSEC

                                  Level: 3

PCR: 03952

Module: SWI

                                  Level: 3

Summary of Contents for 86253-07



































Reviews: