2. Press and hold the START/PAUSE button. After about three
seconds the current cycle status light will turn off.
3. Continue holding the START/PAUSE button for another 7 - 8
seconds until the SPIN light comes on then release the button.
4. If the lid was unlocked, the LID LOCK light will come on
and the lid will lock. Once locked, the machine will start to
drain and spin.
5. After the final spin/drain step the control will reset to normal
operation.
Feature Configuration - Through Serial
Nos. Beginning 1810
Dipswitch Configuration
Dipswitches exist only on models through Serial Nos. beginning
1810.
OFF
ON
Switch 1
120 Volt AC Sup-
ply
240 Volt AC Sup-
ply
Switch 2
Spray Rinse Enable Spray Rinse Disa-
bled
Switch 3
Regulated Water
Temperature/Fill
Levels
Unregulated Water
Temperature/Fill
Levels
Switch 4
Leak and Slow
Drain Errors Off
Leak and Slow
Drain Errors On
Switch 5
Pausing Allowed,
Rapid Advance
Disabled
Rapid Advance En-
abled
Switch 6
Spin Retry Extra
Time Enabled
Spin Retry Extra
Time Disabled
Switch 7
Suds Routine Extra
Time Enabled
Suds Routine Extra
Time Disabled
Switch 8
Unused
Unused
Table 8
Switch 2: When set to OFF, spray rinse is enabled and the Eco
Cycles use a spray rinse. When set to ON, spray rinse is disabled
and deep tub fills are used for rinse steps.
Switch 3: When set to ON, water temperature and fill levels are
used for the specific type/region of the machine. When set to
OFF the U.S.A. default water temperatures and fill levels are
used if the temperature and fill levels in use are not already great-
er.
Switch 5: When Pausing Allowed, Rapid Advance Disabled (Off)
is selected, pressing the Start/Pause button during Run Mode will
pause the cycle. When Rapid Advance Enabled (On) is selected,
pressing the Start/Pause button during Run Mode will advance
the current cycle step to the next enabled step.
Switch 6: When set to Spin Retry Extra Time Enabled (Off) the
cycle step time will pause for the amount of time used up to that
point in the current step. This can happen twice per spin step dur-
ing a cycle if the unbalance switch is hit or if an OBL check (at
90 RPM or 350 RPM) needs to restart the spin to rebalance the
load. Additional OBL failures in the same cycle step will not
pause the time but will still restart the spin. When set to Spin Re-
try Extra Time Disabled (On), time will not pause for respins.
Switch 7: When set to Suds Routine Extra Time Enabled (Off)
the cycle step time will pause when Suds Removal Routines are
being run. Up to two Suds Removal Routines are allowed per cy-
cle. When set to Suds Routine Extra Time Disabled (On), time
will not pause if a Suds Removal Routine is run and will only al-
low one Suds Removal Routine to be run per cycle.
Feature Configuration - Starting Serial
Nos. beginning 1810
Audio Signals
An audio signal will sound for three seconds at the end of each
cycle. To turn it off, hold the Extra Rinse button for three sec-
onds. Hold it again for three seconds to turn the signal back on. A
one-second tone will sound to confirm that the End of Cycle sig-
nal is turned off or on.
Audio signals will sound when a knob selection is changed and
when the Start/Pause or Extra Rinse buttons are pressed. To turn
them off, hold the Extra Rinse button for 10 seconds. Hold it
again for 10 seconds to turn the signals back on. A three-second
tone will sound to confirm that these signals are turned off or on.
In addition, the Status lights will be lit in an upward pattern when
the signal is turned on. The lights will be lit in a downward pat-
tern when the signal is turned off.
Rapid Advance
When Rapid Advance is enabled, pressing the START/PAUSE
button during Run Mode will advance the current cycle step to
the next enabled step.
How to Enter Rapid Advance Mode:
1. Press and hold both the START/PAUSE and EXTRA RINSE
button for three seconds. The Status lights will be lit in an up-
ward pattern when rapid advance is turned on.
2. Press START/PAUSE button to advance through the cycle.
3. To exit rapid advance, press and hold both the START/
PAUSE and EXTRA RINSE button for three seconds. The
lights will be lit in a downward pattern when the signal is
turned off.
Troubleshooting Diagnostics
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
14
Part No. 204666ENR1
Summary of Contents for ZWN43RSN115CW01
Page 2: ......
