4. When
Ft En
appears in the display, press the START (enter)
keypad. The current Factory Test status will appear in the dis-
play.
on
= Option Enabled (factory default setting)
oFF
= Option Disabled
5. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Lucky Cycle
LUC-
This option allows the owner to program the machine to provide
a free or reduced vend cycle to users after a certain number of
machine cycles have occurred.
1. Control must be in Manual Mode. Refer to
2. Press the DELICATES (
∧
) or the COLD (
∨
) keypad until
Prog
appears in the display. Press the START (enter) keypad,
and
AtS 1
will appear in the display.
3. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to scroll
through the programmable options until
LUC-
appears in the
display.
4. When
LUC-
appears in the display, press the START (enter)
keypad. There are three programmable Lucky Cycle options.
Refer to
.
Display
Lucky Cycle Options
LUC 1
Lucky Cycle Day(s) of
Week / Enable On/Off
for pro-
gramming.
LUC 2
Lucky Cycle Number
(0-255)
LUC 3
Lucky Cycle Display Op-
tion On/Off
ON = Free vend. Lucky
cycle active after 4.25 mi-
nutes in Ready Mode.
OFF = Vend must be en-
tered. Remaining vend is
free. For example, after
entering a coin the price
will count down by Coin
1 value until vend is satis-
fied.
Table 12
NOTE: When the Lucky Cycle conditions have been
met, the display will show
FrEE
when the Display
Option is set to On.
5. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Water Temperature Indicator
tP ind
This option allows the owner to program the water temperature
indicator. If the Wash Temp Display is enabled the actual water
valve fill temperature will be indicated during the fill, supply, ag-
itate, or soak step by lighting the LED corresponding to the actual
temperature. If the option is enabled the control will light up the
LED of the water temperature for the current segment that the
control is in while running after the first fill.
1. Control must be in Manual Mode. Refer to
2. Press the DELICATES (
∧
) or the COLD (
∨
) keypad until
Prog
appears in the display. Press the START (enter) keypad,
and
AtS 1
will appear in the display.
3. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to scroll
through the programmable options until
tP ind
appears in
the display.
4. When
tP ind
appears in the display, press the START (en-
ter) keypad. The current Water Temperature Indicator status
will appear in the display.
on
= Option Enabled
oFF
= Option Disabled (factory default setting)
5. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to change
the current status.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Programmable Close Lid Display
PCdL
This option allows the owner to enable or disable allowing the
control to display the corresponding command to close the lid
along with the cycle time.
1. Control must be in Manual Mode. Refer to
2. Press the DELICATES (
∧
) or the COLD (
∨
) keypad until
Prog
appears in the display. Press the START (enter) keypad,
and
AtS 1
will appear in the display.
3. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to scroll
through the programmable options until
PCdL
appears in the
display.
4. When
PCdL
appears in the display, press the START (enter)
keypad. The current status will appear in the display.
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
64
Part No. 204370ENR1
Summary of Contents for SWNNC2HP115TQ01
Page 2: ......
