ALLIANCE SWNNC2HP115TQ01, Original Instructions Manual

Page: 37 / 90

Vend Price 1
AtS 1
This option allows the owner to set the vend price for all cycles,
but otherwise specifically for NORMAL HOT. This price should
be set before all other prices. This vend price will be shown in the
display when NORMAL HOT is selected.
1. Control must be in Manual Mode. Refer to
How to Enter the
Manual Mode .
2. Press the DELICATES (
∧
) or the COLD (
∨
) keypad until
Prog
appears in the display. Press the START (enter) keypad,
and
AtS 1
will appear in the display.
3. Press the START (enter) keypad. All cycle LEDs will be lit to
show all cycle prices are being programmed.
NOTE: To go back to the current programmable op-
tion without changing the value, press the WARM (<)
keypad.
4. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
5. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Vend Price 2
AtS 2
This option allows the owner to set the vend price for NORMAL
WARM. This vend price will be shown in the display when
NORMAL WARM is selected.
1. Control must be in Manual Mode. Refer to
How to Enter the
Manual Mode .
2. Press the DELICATES (
∧
) or the COLD (
∨
) keypad until
Prog
appears in the display. Press the START (enter) keypad,
and
AtS 1
will appear in the display.
3. The keypad LEDs will be lit to show which cycle price is be-
ing programmed.
4. When
AtS 2
appears in the display, press the START (enter)
keypad.
NOTE: To go back to the current programmable op-
tion without changing the value, press the WARM (<)
keypad.
5. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Vend Price 3
AtS 3
This option allows the owner to set the vend price for a NOR-
MAL COLD. This vend price will be shown in the display when
NORMAL COLD is selected.
1. Control must be in Manual Mode. Refer to
How to Enter the
Manual Mode .
2. Press the DELICATES (
∧
) or the COLD (
∨
) keypad until
Prog
appears in the display. Press the START (enter) keypad,
and
AtS 1
will appear in the display.
3. The keypad LEDs will be lit to show which cycle price is be-
ing programmed.
4. When
AtS 3
appears in the display, press the START (enter)
keypad.
NOTE: To go back to the current programmable op-
tion without changing the value, press the WARM (<)
keypad.
5. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
6. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Vend Price 4
AtS 4
This option allows the owner to set the vend price for a PERM
PRESS HOT. This vend price will be shown in the display when
PERM PRESS HOT is selected.
1. Control must be in Manual Mode. Refer to
How to Enter the
Manual Mode .
2. Press the DELICATES (
∧
) or the COLD (
∨
) keypad until
Prog
appears in the display. Press the START (enter) keypad,
and
AtS 1
will appear in the display.
3. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to scroll
through the programmable options until
AtS 4
appears in the
display.
4. The keypad LEDs will be lit to show which cycle price is be-
ing programmed.
5. When
AtS 4
appears in the display, press the START (enter)
keypad.
NOTE: To go back to the current programmable op-
tion without changing the value, press the WARM (<)
keypad.
6. Press the DELICATES (
∧
) or the COLD (
∨
) keypad to in-
crease or decrease the value of the active digit and the START
(enter) keypad to enter the value of the digit and advance to
the next digit.
7. Press the START (enter) keypad when the correct value ap-
pears in the display. The new value is saved and the next op-
tion will appear in the display.
Programming Control
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
37 Part No. 204370ENR1