ALLIANCE SCA030FN Original Instructions Manual Download Page 73

Page: 73 / 157

No Water Flow Error

E nFLo

(No Cold Hard Fill - Optional)

Is the water turned

on?

Are fill valve inlet

screens plugged?

Yes

Turn on water.

Is there a fill step

programmed?

Clean inlet screens

and re-test.

Yes

Run Factory Test.

Yes

Add/edit a fill step

in programming.

Test Cold Hard Fill

during CLD HrD fill

test step.

(J)

Is there 24VDC

between H11-1 and

H11-4 on AP1 ?

Replace AP1.

(J1)

Ensure plugs are

attached to the

valves and re-check

voltages at the

valves. Is voltage

present?

Yes

Replace mixing

valve.

Yes

Check wiring

between valve and

AP1

Troubleshooting

DO NOT COPY or TRANSMIT

Part No. F8677701EN

Summary of Contents for SCA030FN






























































































































































Search results

Summary of Contents for SCA030FN

Reviews:

Related manuals for SCA030FN

Brands by name

Popular brands

ALLIANCE SCA030FN, Original Instructions Manual

Search results

Summary of Contents for SCA030FN

Reviews:

Related manuals for SCA030FN

Brands by name

Popular brands