manualshive.com logo in svg

Allen-Bradley ProcessLogix 1757-SRM, Installation Instructions Manual, Page: 18 / 36

Share
Download
Allen-Bradley ProcessLogix 1757-SRM Installation Instructions Manual Download Page 18

18

    ProcessLogix and ControlLogix System Redundancy Module 

Publication

 1757-IN092E-EN-P - November 2007

Flash Upgrade the Modules

To flash upgrade the modules to the latest firmware revision, perform this 
procedure.

1.

Go to http://support.rockwellautomation.com and download the 
latest firmware revision for your 1757-SRM module.

2.

Download and install the ControlFLASH Firmware Upgrade Kit.

3.

Apply power to only one redundant chassis.

4.

Wait for the module to roll display: FACT BOOT FLSH UPDT 
REQD.

5.

Start your ControlFLASH Firmware Upgrade Kit and apply the latest 
firmware to the module.

For additional information on identifying and upgrading your 
1757-SRM module, see the ControlFLASH Firmware Upgrade Kit 
Quick Start, publication 1756-QS105.

6.

Verify that the module displays PRIM, indicating a successful flash 
upgrade.

7.

Turn off the power to the redundant chassis used in step 3.

8.

Apply power to the other redundant chassis.

IMPORTANT

Back up any programs or data that you have saved to a device. 
When you upgrade firmware, all old data will be overwritten.

IMPORTANT

Make sure you know the serial number from your original 
firmware disk. To upgrade to the latest firmware revision, 
such as 4.

x

, you will need to provide the original serial 

number. If you don’t have the serial number, refer to 
Rockwell Automation Support on the back cover.

Summary of Contents for ProcessLogix 1757-SRM





































Reviews:

No comments