Allen-Bradley ControlLogix 1756-OF4 Installation Instructions Manual Download Page 19

ControlLogix Voltage/Current Output Module    

19

Publication

  1756-IN016B-EN-P - November 2003

RTB Screw Torque (NEMA)

7-9 inch-pounds (0.8-1Nm) 

Module Keying (Backplane)

Electronic

RTB Keying

User defined

RTB and Housing

20 Position RTB (1756-TBNH or TBSH)

(1)

Conductors

Wire Size

Category

#22 to #14 AWG (0.324 to 2.08 sq. mm) stranded

(1)

3/64 inch (1.2mm) insulation maximum
2

(2)

(3)

Screwdriver Width for RTB

5/16 inch (8mm) maximum

Environmental Conditions

Operating Temperature

IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
0 to 60°C (32 to 140°F)

Storage Temperature

IEC 60068-2-1 (Test Ab, Un-packaged Non-operating 
Cold),
IEC 60068-2-2 (Test Bb, Un-packaged Non-operating 
Dry Heat),
IEC 60068-2-14 (Test Na, Un-packaged Non-operating 
Thermal Shock):
-40 to 85°C (-40 to 185°F)

Relative Humidity

IEC 60068-2-30 (Test Db, Un-packaged Non-operating 
Damp Heat):
5 to 95% non-condensing

Vibration

IEC60068-2-6 (Test Fc, Operating):
2g @ 10-500Hz

Operating Shock

IEC60068-2-27 (Test Ea, Unpackaged shock):
30g

Non-operating Shock

IEC60068-2-27 (Test Ea, Unpackaged shock):
50g

Emissions

CISPR 11:
Group 1, Class A

ESD Immunity

IEC 61000-4-2:
6kV contact discharges
8kV air discharges

Radiated RF Immunity

IEC 61000-4-3:
10V/m with 1kHz sine-wave 80%AM from 30MHz to 
1000MHz
10V/m with 200Hz 50% Pulse 100%AM at 900Mhz

EFT/B Immunity

IEC 61000-4-4:
±2kV at 5kHz on signal ports

AB PLCs

Summary of Contents for ControlLogix 1756-OF4





















Reviews: