Allen-Bradley ControlLogix 1756-IF6CIS Installation Instructions Manual Download Page 20

Publication

 1756-IN579A-EN-P - March 2003

PN 957678-01

Supersedes Publication 1756-IN-EN-P - October 2000

Copyright © 2003 Rockwell Automation. All rights reserved. Printed in the U.S.A.

The following information applies when 
operating this equipment in hazardous 
locations:

Informations sur l’utilisation de cet équipement 
en environnements dangereux :

Products marked “CL I, DIV 2, GP A, B, C, D” are 
suitable for use in Class I Division 2 Groups A, B, 
C, D, Hazardous Locations and nonhazardous 
locations only. Each product is supplied with 
markings on the rating nameplate indicating the 
hazardous location temperature code. When 
combining products within a system, the most 
adverse temperature code (lowest “T” number) 
may be used to help determine the overall 
temperature code of the system. Combinations 
of equipment in your system are subject to 
investigation by the local Authority Having 
Jurisdiction at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne 
conviennent qu’à une utilisation en environnements de 
Classe I Division 2 Groupes A, B, C, D dangereux et 
non dangereux. Chaque produit est livré avec des 
marquages sur sa plaque d’identification qui indiquent 
le code de température pour les environnements 
dangereux. Lorsque plusieurs produits sont combinés 
dans un système, le code de température le plus 
défavorable (code de température le plus faible) peut 
être utilisé pour déterminer le code de température 
global du système. Les combinaisons d’équipements 
dans le système sont sujettes à inspection par les 
autorités locales qualifiées au moment de 
l’installation.

!

WARNING

EXPLOSION HAZARD

·

Do not disconnect 
equipment unless power 
has been removed or the 
area is known to be 
nonhazardous. 

·

Do not disconnect 
connections to this 
equipment unless power 
has been removed or the 
area is known to be 
nonhazardous. Secure any 
external connections that 
mate to this equipment by 
using screws, sliding 
latches, threaded 
connectors, or other means 
provided with this product.

·

Substitution of components 
may impair suitability for 
Class I, Division 2.

·

If this product contains 
batteries, they must only be 
changed in an area known 
to be nonhazardous.

AVERTISSEMENT

!

RISQUE D’EXPLOSION

·

Couper le courant ou s’assurer 
que l’environnement est 
classé non dangereux avant 
de débrancher l'équipement.

·

Couper le courant ou s'assurer 
que l’environnement est 
classé non dangereux avant 
de débrancher les 
connecteurs. Fixer tous les 
connecteurs externes reliés à 
cet équipement à l'aide de vis, 
loquets coulissants, 
connecteurs filetés ou autres 
moyens fournis avec ce 
produit.

·

La substitution de composants 
peut rendre cet équipement 
inadapté à une utilisation en 
environnement de Classe I, 
Division 2.

·

S’assurer que l’environnement 
est classé non dangereux 
avant de changer les piles.

Summary of Contents for ControlLogix 1756-IF6CIS





















Reviews: