Allen-Bradley CompactLogix EtherNet/IP 1768-EWEB Installation Instructions Manual Download Page 15 | Manualshive

Page: 15 / 24

Allen-Bradley CompactLogix EtherNet/IP 1768-EWEB Installation Instructions Manual Download Page 15

CompactLogix EtherNet/IP Web Server Module

15

Rockwell Automation Publication 1768-IN007B-EN-P - August 2010

Connect the Module

Attach the RJ45 connector to the Ethernet port on the bottom of the module.

WARNING:

If you connect or disconnect the cable with power

applied to this module or any device on the network, an electrical
arc can occur. This could cause an explosion in hazardous location
installations. Be sure that power is removed or the area is
nonhazardous before proceeding.

IMPORTANT

We recommend connecting the module to the network via a
100 MB Ethernet switch, which will reduce collisions and lost
packets and increase network bandwidth. For detailed
EtherNet/IP connection information, see the EtherNet/IP
Modules in Logix5000 Control Systems User Manual, publication

ENET-UM001

.

Item

Description

1

Ethernet port

1

31611-M

AB Drives

«
...
13
14
15
16
17
...
»

Summary of Contents for CompactLogix EtherNet/IP 1768-EWEB

























Reviews:

No comments