Allen-Bradley 5069-IA16 User Manual Download

Page: 93 / 296

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

Input Module Features

Chapter 3

Events

You can use the Events feature to trigger events.

The modules support up to four event configurations.

The following can trigger events:

• An input state change.
• A counting input done bit change.
• A pattern of input state changes on multiple module inputs.

You must use the Data with Events connection type in the Module Definition
to use the Events feature.

Event Definition

You define an event. When you define an event, remember the following:

• The event definition parameters are shown on Events

category in the

Module Properties dialog box. The parameters are read-only in the
dialog box as shown in this example.

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

SA P

MOD P

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

Standard Modules

™

NET B1

LINK B1

NET A1

LINK A1

NET A2

LINK A2

SPEED X1

LINK X1

RUN

FORCE

FAN 1

FAN 2

Compact

Logix

5480

5069-L46ERMW

CONTROLLER

UPS

R
B
F

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

IMPORTANT

The following Compact 5000 I/O standard input modules support the
Events feature:

• 5069-IB16F

• 5069-IB6F-3W

IMPORTANT

: You cannot

change the parameters on
this dialog box.

Summary of Contents for 5069-IA16









































































































































































































































































































Search results

Summary of Contents for 5069-IA16

Reviews:

Related manuals for 5069-IA16

Brands by name

Popular brands

Allen-Bradley 5069-IA16, User Manual

Search results

Summary of Contents for 5069-IA16

Reviews:

Related manuals for 5069-IA16

Brands by name

Popular brands