Allen-Bradley 5069-IA16 User Manual Download | Manualshive

Page: 60 / 296

background image

60

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

Chapter 1

Digital Module Operation in a Control System

Use with Safety Controllers

You can only use the Compact GuardLogix 5380 or GuardLogix 5580
controllers with the Compact 5000 I/O safety modules. Restrictions apply
regarding how the controllers can use the I/O modules. The restrictions are
described in

Controller and Software Compatibility on page 18

For more information on which controllers you can use with Compact 5000
I/O safety modules, see

Table 3 on page 19

You must use the Logix Designer application, version 32 or later, to configure
the Compact 5000 I/O safety modules.

Determine Conformity

ATTENTION:

Use only appropriate components or devices that comply with

the relevant safety standards and meet the required safety integrity level or
Performance Level and safety category.

• Conformity to the requirements of the relevant safety standards must be

determined for the entire system by conducting a risk assessment.

• Use devices properly according to the installation environment,

performance rating, and functions of the machine.

• Use devices within their specified ratings.

• We recommend that you consult a certification body regarding assessment

of conformity to the required safety integrity level or Performance Level.

You are responsible for confirming compliance with the applicable standards for
the entire system. You must read, understand, and fulfill the functional safety
requirements of the standard applicable to your safety application.

«
...
58
59
60
61
62
...
»

Summary of Contents for 5069-IA16









































































































































































































































































































Reviews:

No comments

Related manuals for 5069-IA16

Brand: Reliance Foundry Pages: 3

Brand: Aichi Pages: 54

Brand: Daewoo Pages: 21

Brand: National Instruments Pages: 28

Liftkar SAL Uni

Brand: SANO Pages: 24

Brand: M-system Pages: 7

Brand: galmar Pages: 8

Brand: ELFON Pages: 48

Brand: PROLIFTS Pages: 44

Brand: ZKTeco Pages: 15

Auto Dialer AVD-45b

Brand: SJE Rhombus Pages: 2

Brand: Aewin Pages: 42

Brand: Cama Pages: 18

TOP LIFT TSK 12000 DJ

Brand: Nussbaum Pages: 56

Brand: ICP DAS USA Pages: 4

Brand: Reliable Pages: 6

Brand: Dahua Pages: 106

ADDIALOG PA 3110

Brand: Addi-Data Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands