Allen-Bradley 5069-IA16 User Manual Download | Manualshive

Page: 56 / 296

background image

56

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

Chapter 1

Digital Module Operation in a Control System

Listen Only

Any controller in the system can listen to the data from an I/O module. An
owner-controller, as described in

Ownership on page 29

, exchanges data with

I/O modules.

Controllers that do not own a module but must listen to data from it use the
following on the Module Definition dialog box:

• Compact 5000 I/O standard modules - Connection = Listen Only Data

• Compact 5000 I/O safety modules - Configured By = External Means.

In this case, the ‘listening’ controller can only listen to input data or ‘echoed’
output data. The listening controller does not own the module configuration
or exchange other data with the module.

During the I/O configuration process, you can specify a Listen Only
connection. For more information on Connection options, see

Definition on page 163

.

5069-OBV8S

SIL2 CPU

5069-L3100ERMS2

Compact GuardLogix

5069-OBV8S

5069-IB8S

5069-IB8S

OUTPUT

OUTPUT

SA

Po

w

er

M

O

D

Po

w

er

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

SA P

ow

er

MOD P

ow

er

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

Standard Modules

Safety Modules

™

NET B1

LINK B1

NET A1

LINK A1

NET A2

LINK A2

SPEED X1

LINK X1

OK

RUN

FORCE

FAN 1

SD

FAN 2

Compact

Logix

5480

B1

A1

1

2

A2

5069-L46ERMW

CONTROLLER

UPS

MP

SA

R
B
F

R

B

F

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

IMPORTANT

Remember the following:

• CompactLogix 5380, CompactLogix 5480, or Compact GuardLogix 5380

controllers cannot make a Listen Only connection to a local Compact
5000 I/O standard module.

The controllers can make a Listen Only connection only to remote
Compact 5000 I/O standard modules.

• If a controller uses a Listen Only connection, the connection must use the

Multicast option.

In this case, all other connections to the module, for example, the
connection of the owner-controller, must also use the Multicast option.

• If a controller uses External Means, the connection must use the

Multicast option.

In this case, all other connections to the module, for example, the
connection of the owner-controller, must also use External Means.

• If a controller attempts to use a Listen Only connection to a module but

the owner-controller connection uses the Unicast option, the attempt at
a Listen Only connection fails.

The ‘Listen Only’ controller receives data from the module as long as a
connection between an owner-controller and module is maintained.

• If a controller attempts to use External Means in a module definition but

the owner-controller connection uses the Unicast option, the attempt to
define the module with External Means fails.

• If the connection between an owner-controller and the module is

broken, the module stops sending data and connections to all ‘listening
controllers’ are also broken.

«
...
54
55
56
57
58
...
»

Summary of Contents for 5069-IA16









































































































































































































































































































Reviews:

No comments

Related manuals for 5069-IA16

Brand: ZKTeco Pages: 18

Brand: Bang & Olufsen Pages: 20

Brand: Bang & Olufsen Pages: 24

BeoSound Ouverture

Brand: Bang & Olufsen Pages: 44

Brand: Yamaha Pages: 108

Brand: cinetto Pages: 56

Brand: Rotary Pages: 16

Brand: PURE Pages: 88

SystemRoMedic EvaDrive450

Brand: Handicare Pages: 37

Brand: Memorex Pages: 2

Brand: Hoshizaki Pages: 10

I/O-SYSTEM 750-610

Brand: WAGO Pages: 14

Oxford MAJOR 190

Brand: Sunrise Medical Pages: 48

Water Quality System EQHP-TWIN 108SP

Brand: Bunn Pages: 2

NANOpure DIamond D11931

Brand: Barnstead|Thermolyne Pages: 56

Brand: ELFON Pages: 48

Brand: Tarfire Pages: 31

Brand: CAME Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands