Allen-Bradley 5069-IA16 User Manual Download | Manualshive

Page: 48 / 296

background image

48

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

Chapter 1

Digital Module Operation in a Control System

By default, the Connection Reaction Time Limit is four times the RPI.

Use the default values for Timeout Multiplier (2) and Network Delay
Multiplier (200). The Network Delay Multiplier value is in terms of
percentage. Thus, 200 means 200%.

For more information on how to specify RPI rates, see the following:

• Compact 5000 I/O standard modules -

• Compact 5000 I/O safety modules -

• Logix5000 Controllers Design Considerations Reference Manual,

publication

Connection Over an EtherNet/IP Network

When you configure a remote Compact 5000 I/O digital module, you must
configure the Connection over EtherNet/IP parameter in the configuration
for the remote adapter that connects the I/O modules to the network. The
configuration choice dictates how input data is transmitted over the network.

The Compact 5000 I/O digital modules use one of the following methods to
transmit data:

• Multicast - Data is sent to all network devices.

If you are using the I/O modules in a redundancy system, you must use
Multicast.

• Unicast - Data is sent to one or more controllers depending on module

configuration.

Unicast is the default setting.

IMPORTANT

To determine what is appropriate, analyze each safety channel. The default
Timeout Multiplier of 2 and Network Delay Multiplier of 200 creates a worst-
case input connection reaction time limit of 4 times the RPI, and an output
connection reaction time limit of 3 times the RPI.

Changes to these parameters must be approved only after a thorough review
by a safety administrator.

«
...
46
47
48
49
50
...
»

Summary of Contents for 5069-IA16









































































































































































































































































































Reviews:

No comments

Related manuals for 5069-IA16

Brand: Abus Pages: 15

Brand: RAPIBREW Pages: 16

Brand: S.E.M. Pages: 6

Brand: Subpac Pages: 15

Brand: Danfoss Pages: 8

Brand: BUCKINGHAM MFG Pages: 7

Brand: jWIN Pages: 13

Brand: Daewoo Pages: 27

Brand: Zonex Pages: 28

Brand: Barnstead Thermolyne Corporation Pages: 32

Brand: Ravaglioli Pages: 68

Brand: TCS Pages: 2

PRODUCTIVITY 2000

Brand: Automation Direct Pages: 8

Brand: PROLIFTS Pages: 44

Brand: CAME Pages: 48

Brand: BAS-IP Pages: 53

Brand: Marshall Amplification Pages: 30

Brand: Forge Electronics Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands