Allen-Bradley 5069-IA16 User Manual Download | Manualshive

Page: 143 / 296

background image

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

143

Safety Module Features

Chapter 5

Safety Output
Module Features

This section describes features that are available only on the Compact 5000
I/O safety output modules, that is, the 5069-OBV8S and 5069-OBV8SK
modules.

The 5069-OBV8S and 5069-OBV8SK modules are safety output module that
uses eight safety outputs. You use the outputs in one of the following ways:

• Sourcing/sinking outputs in Bipolar Output mode
• Sourcing outputs in Sourcing Output mode.

The only difference between the 5069-OBV8S and 5069-OBV8SK modules is
that the 5069-OBV8SK module has conformal coating.

Safety Application Suitability Levels

describes the safety application suitability levels for a 5069-OBV8S

module.

Table 44 - Safety Application Suitability for 5069-OBV8S Module

Suitability Level

Conditions

Notes

Safety applications that are rated up to, and
including,

SIL CL3, PLd, Cat. 3

as defined in IEC

61508, IEC 61511, IEC 62061, and ISO 13849-1.

• The module uses

single-channel

mode.

• Output Mode is Sourcing.

• Point Mode is Safety Pulse Test.

Consider the following:

• The channel mode type, that is, single or

dual, affects Category. You can use the
modules in SIL CL3, PLe applications
regardless of channel mode type.
The determining factor to whether a
Compact 5000 I/O safety module resides
in a SIL CL3, PLe, Cat. 4 safety application
is that the overall safety architecture be a
dual-channel system.

• The requirement that Point Mode be

Safety Pulse Test assumes that only the
safety modules provide diagnostics to a
specific Suitability Level.
The larger safety system within which the
safety I/O module resides can provide the
diagnostics necessary to achieve the
stated Suitability Level without the
requirement that Point Mode be Safety
Pulse Test.

Safety applications that are rated up to, and
including,

SIL CL3, PLe, Cat. 4

as defined in IEC

61508, IEC 61511, IEC 62061, and ISO 13849-1.

• Output Mode is Bipolar.

Or

• The module uses

single-channel

mode.

• Output Mode is Sourcing.

• Point Mode is Safety Pulse Test.

• The channel is connected to an IEC 60947 certified actuator or contactor.

Additionally, you must use shredded cable or cable trunk to eliminate short
circuit faults on the channel.

Or

• The module uses

dual-channel

mode.

• Output Mode is Sourcing.

• Point Mode is Safety Pulse Test.

«
...
141
142
143
144
145
...
»

Summary of Contents for 5069-IA16









































































































































































































































































































Reviews:

No comments

Related manuals for 5069-IA16

Brand: Sven Pages: 12

Brand: Eaton Pages: 4

Brand: Eaton Pages: 10

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Water Jet Lightning

Brand: Oase Pages: 28

Brand: Oase Pages: 9

EtherCAT Compact67 Slim

Brand: elco Pages: 28

Brand: ShoreStation Pages: 19

Brand: BVM Pages: 23

Brand: Dahua Pages: 18

PORTAGANTRY 11000

Brand: REID LIFTING Pages: 21

Brand: Audiocenter Pages: 40

Brand: ATEN Pages: 176

Brand: LSS Pages: 14

Brand: FAAC Pages: 16

Brand: Jensen Pages: 2

Brand: Roadstar Pages: 80

Brand: salmson Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands