Allen-Bradley 5069-IA16 User Manual Download

Page: 126 / 296

126

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

Chapter 4

Output Module Features

Forcing

Use a force to override data that your logic either uses or produces.

• Test and debug your logic.

• Temporarily maintain normal system operations when an input device

has failed.

Use forces only as a temporary measure. They are not intended to be a
permanent part of your application.

Make sure that you understand this before you use forces.

Enable Forces

For a force to take effect, you enable forces. You can only enable and disable
forces at the controller level.

• You can enable I/O forces and SFC forces separately or simultaneously.

• You cannot enable or disable forces for a specific module, tag collection,

or tag element.

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

SA P

MOD P

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

Standard Modules

™

NET B1

LINK B1

NET A1

LINK A1

NET A2

LINK A2

SPEED X1

LINK X1

RUN

FORCE

FAN 1

FAN 2

Compact

Logix

5480

5069-L46ERMW

CONTROLLER

UPS

R
B
F

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

ATTENTION:

Forcing can cause unexpected machine motion that could

injure personnel. Before you use a force, determine how the force affects
your machine or process and keep personnel away from the machine area.

• Enabling I/O or SFC forces causes your machine or process to go to another

state or phase.

• Removing forces can still leave forces in the enabled state.

• If forces are enabled and you install a force, the new force immediately

takes effect.

Summary of Contents for 5069-IA16









































































































































































































































































































Search results

Summary of Contents for 5069-IA16

Reviews:

Related manuals for 5069-IA16

Brands by name

Popular brands

Allen-Bradley 5069-IA16, User Manual

Search results

Summary of Contents for 5069-IA16

Reviews:

Related manuals for 5069-IA16

Brands by name

Popular brands