Allen-Bradley 5069-IA16 User Manual Download

Page: 104 / 296

104

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

Chapter 3

Input Module Features

Test Output Recovery After Overload or Short Circuit to
Ground Condition

Table 21

describes test output recovery after overload or short circuit to ground

conditions occur.

Table 21 - Test Output Recovery - Compact 5000 I/O Safety Input Modules

Cause of Fault

Module Operating Conditions

Correction

Recovery Time

Overload Condition

• Test Output Point Mode - Pulse Test, Power

Supply, or Muting Lamp.

• Test Output Data tag = 1.

• Overload current ≥ 0.7 A.

Remove the load from the test output point.

After the condition is corrected, and the test
output is returned to the safe state, it recovers
in whichever of the following times are higher:

• 10 seconds

• Input Error Latch Time - This time is set on

the Input Points category of the Module
Properties dialog box.
To see where to set the Input Error Latch
Time, go to

page 203

Short Circuit to Ground
Condition

• Test Output Point Mode - Pulse Test, Power

Supply, or Muting Lamp.

• Test Output Data tag = 1.

• Test output is connected directly to ground.

One of the following:

• If the Point Mode for the test output is Pulse

Test or Power Supply when the Short Circuit
condition is detected, the condition can be
corrected but you cannot set the test output
to a safety state.

• If the Point Mode for the test output is

Muting Lamp and the output is on when the
Short Circuit condition is detected, the
ShortToHigh is detected as a muting fault.

Summary of Contents for 5069-IA16









































































































































































































































































































Search results

Summary of Contents for 5069-IA16

Reviews:

Related manuals for 5069-IA16

Brands by name

Popular brands

Allen-Bradley 5069-IA16, User Manual

Search results

Summary of Contents for 5069-IA16

Reviews:

Related manuals for 5069-IA16

Brands by name

Popular brands