manualshive.com logo in svg

Allen-Bradley 1757-FFLD2, User Manual

Share
Download
Allen-Bradley 1757-FFLD2 User Manual Download Page 125

Rockwell Automation Publication 1757-UM012A-EN-P - July 2011

125

Chapter

 9

Diagnostic Web Pages

Introduction

This chapter describes the diagnostic web pages of the linking device.

H1 Live List

The H1 Live List page is a list of devices on the linking device’s H1 ports. Each 
port on the linking device is listed as a separate network and the linking device 
appears as a device on each network list.

A device remains in this Live List as long as it responds properly to the token sent 
from the Link Active Scheduler (LAS). The LAS will remove a device from the 
Live List if the device does not use the token or immediately return it to the LAS 
after three successive tries. The LAS periodically sends messages to the addresses 
of devices not in the Live List. If a device returns a message, the LAS adds the 
device to the Live List.

Topic

Page

H1 Live List

125

VCR Pages

127

Ethernet Pages

129

Diagnostic Log Files

132

Summary of Contents for 1757-FFLD2

























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands